Replacement Brake Assemblies, Drums and Bearings for 2007 Extreme Megalite 19LT Travel Trailer

Question

Question:

I have a 2007 Extreme Megalite 19LT with 3,500 LB axles. I want to replace the brake assemblies with never adjust assemblies, bearing, and all associated parts. Can you tell me what part #s and quantities I will need? Thanks,

asked by: Brett D

0

Expert Reply:

For new brake assemblies, I'd recommend the etrailer.com 10 inch Self Adjusting assemblies, part # AKEBRK-35L-SA for the left side and # AKEBRK-35R-SA for the right. For each assembly, you'll need 4 nuts, part # 6-17 and 4 lock washers, part # 5-8.

Closely examine the armature surface of your existing brake drums (inside surface that the brake magnet rides against). If the surface is pitted or grooved, I'd recommend replacing the hub/drum so it doesn't prematurely wear the magnets on the bake assemblies.

3500 lb axles commonly use the L68149 inner and L44649 outer bearing. A wheel bolt pattern on 5 lug on a 4-1/2 inch bolt circle is most common. If this is the case with your trailer, you can use the # AKHD-545-35-K hub drum, which includes the bearings, races, grease seal, grease cap and lug nuts. You'll want to examine your current bearings to confirm that you have the L68149 inner and L44649 outer bearing.

If you just need the bearings, and you confirm that your hub uses the bearings mentioned above, use the # BK2-100 bearing kit. Each kit includes one inner bearing and race, one outer bearing and race, one grease seal, a Cotter pin and a tang washer. You'll need one bearing kit per wheel.

If your bearings or wheel bolt pattern is different that what I've mentioned above, let me know and I'd be happy to make other recommendations for you.

expert reply by: Mike L

0

Answer 1

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 2

You will need to do some measuring to determine if the 10 Inch Electric Brake Assembly LH, item #AKEBRK-35L, is the correct assembly for your trailer. Measure the diameter of the mounted brake shoe, the width of the lining and the distance between…

view full answer...

Answer 3

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 4

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 5

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 8

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 11

I can definitely help you find the correct replacement hub and bearings for your Dexter P-12 SLR axle, but since part of the serial number was unreadable you will need to take a few simple steps to identify which bearings your axle uses. The easiest…

view full answer...

Answer 12

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Replacement Brake Assemblies, Drums and Bearings for 2007 Extreme Megalite 19LT Travel Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching