Trailer Hitch Lock Availability

Question

Question:

I lost the key to our trailer hitch lock. I had a locksmith get the lock off for me, and I am now trying to replace the lock and key. I have a picture to send but I cant see your e-mail until I send this. Can you help me?

asked by: Donna S

0

Expert Reply:

We carry several trailer hitch locks that could work for you (see link), like the part # e98881 which is a very popular option that we offer.

expert reply by: Jameson C

0

Answer 1

Sounds like you have a 2-1/2 inch hitch on your 2016 Ford F-350 and need a longer hitch pin lock to fit it. The part #e98881 would be exactly what you would need since this lock is designed to fit 2-1/2 inch hitches.

view full answer...

Answer 2

We do have a way for you to lock your ball mount to your hitch receiver but unfortunately, the Blue Ox #BX88212 is not able to be keyed alike. For another solution,our etrailer.com lock #e98881 fits 2-1/2 inch Class V hitch receivers and can be keyed…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 9

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 10

Thank you for the photos and sorry to hear about your truck! The unique design of the B&W Tow & Stow 2-Ball Mount - Compatible with GM MultiPro Tailgate #BWTS20066BMP is that angled section that meets with the shank part of the ball mount. On…

view full answer...

Answer 11

There is a way for you to not only lock the B&W Tow & Stow 3-Ball Mount - Compatible with GM MultiPro Tailgate - 2.5" Hitch - 148K #BWTS20067BMP to your 2-1/2 inch trailer hitch, but also the ball platform to the mount, and the hitch…

view full answer...

Answer 12

Hi Robert, The Curt Pintle Hook #C45908 would require that your EZ Loader boat trailer has a lunette ring for the coupler. From what I can see the 26-30ET should have a surge brake coupler that would couple to a standard ball mount. You'll need…

view full answer...

Trailer Hitch Lock Availability

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching