Installation Instructions an User Manual for the Bulldog Jack part # BD180304

Question

Question:

I need a spec sheet for the jack #180304 is a Bulldog. Can you provide this to me.

asked by: Yazmin V

0

Expert Reply:

It sounds like you are looking for the user manual for the Bulldog Jack part # BD180304 that you have. I attached a couple pictures that have both pages of the manual for your jack.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The overall length of the Replacement Topwind Handle w/ Claw Knob for etrailer and Ram Square, Direct Weld Jacks #TJD-7000-HD is 10-1/2 inches. The center to center length is 9 inches. I've attached a photo to assist.

view full answer...

Answer 2

The innermost tube of the Square Direct Weld Jack w/ Footplate #TJD-8000S is actually the drop leg and is less than 2". The black outer tubing is 2-1/4" and the aluminum inner tube is 2".

view full answer...

Answer 3

You won't want to cut a jack like the Square Direct Weld Jack #TJD-8000, with the issue being that doing so you would cut the lift rod inside the jack, not to mention void the warranty, and compromise its capacity. So I would avoid doing that,…

view full answer...

Answer 4

The issue is that there is a screw inside the jack that turns in either direct to raise or lower the jack. It threads through a fixed nut. At the very top of the screw the threads are all mashed up so that the leg can't just fall out. Basically…

view full answer...

Answer 5

When the Pipe Mount Swivel Style Trailer Jack with Foot - Topwind - 15" Travel - 2,000 lbs. #DL22682 is fully extended the distance from the center of the weld-on spud to the foot is 29-3/4 inches. When this is fully retracted the distance is…

view full answer...

Answer 6

I took some measurements of the Dutton-Lainson Pipe Mount Swivel Style Trailer Jack with Foot item #DL22682. The bottom of the handle sits right at 11" above the center of the mounting tube. This jack has our largest length between the pipe…

view full answer...

Answer 7

Looking at the BAL Retract-A-Spare it has a much different design than the Lippert Spare Tire Winch #LC159056 you found. You may be able to mount the new winch so it will still work on your trailer but as we do not have both the products here with…

view full answer...

Answer 8

Yes we have the Redarc In-Vehicle BCDC Battery Charger #RED96FR which essentially is the same thing as the charging system you referenced as it gives you a way to enhance the charging circuit ran to your 7-way to put the best charge on the trailer…

view full answer...

Answer 9

I do have an option for you but the Pro Series Round, Pipe-Mount Swivel Jack w/ Footplate part #PS1401420303 does not include a grease fitting for easy greasing. I recommend Round, Pipe Mount Swivel Jack w/ Footplate - Weld On part #TJP-7002S-B which…

view full answer...

Answer 10

If you aren't familiar with a jack like Square Direct Weld Jack #TJD-12000SP-R2 it can have a little bit of a learning curve. Here is how it works: As you probably know the jack leg retracts quickly. First make sure the jack is not supporting a…

view full answer...

Answer 11

The main difference between the Square Direct Weld Jack part #TJD-12000SP-F2 and part #TJD-12000SP-R2 is the location of the plunger for the drop leg. The former has the plunger on the side of the crank handle and the latter has the plunger adjacent…

view full answer...

Answer 12

The Square Direct Weld Jack part #TJD-12000SP-F2 can be used in tandem. The only thing you would need to do this would be a cross shaft which would be some sort of bar that attaches the two output shafts to one another. This is assuming you want both…

view full answer...

Installation Instructions an User Manual for the Bulldog Jack part # BD180304

Product Page this Question was Asked From

Continue Researching