Hitch Recommendation for a 1990 Ford Bronco

Question

Question:

hitch for 90 bronco

asked by: Nick N

0

Expert Reply:

For a hitch for your 1990 Ford Bronco you would want the part # C15300.

I attached an install video for you to check out as well.

expert reply by: Jameson C

0

Answer 1

I checked with Curt and the distance between the vertical mounting flanges of the Curt #C15300 is 33.312 inches.

view full answer...

Answer 2

Curt Class V hitch #C15300 is a confirmed fit on your 1987 Ford F-150. To help you determine if it will be compatible with your skid plate I went to our warehouse and took a measurement of the hitch to find out the distance from the mounting brackets…

view full answer...

Answer 3

I spoke with my Curt representative, who tells me that the front face of the receiver would sit 10-3/4 inches rearward of the rear-most mounting hole. If you find the rear most mounting hole in the underside of the frame member and measure 10-3/4…

view full answer...

Answer 4

I spoke with my contact at Curt to obtain the mounting bolt hole locations for the Trailer Hitch Receiver, #C15300 on a 1993 Ford F-150. I have attached a picture to illustrate these measurements. As for repositioning the spare tire, you may need to…

view full answer...

Answer 5

The highest rated available trailer hitches I can find for a 1996 Ford Bronco are Class IV hitches. We carry the CURT Trailer Hitch, #14001. This hitch does not fit cab and chassis models or models with a roll pan bumper. It is a Class IV hitch rated…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 9

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

To add a hitch to your 2024 Toyota RAV4, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and a 600…

view full answer...

Hitch Recommendation for a 1990 Ford Bronco

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching