Recommended Aluminum Trailer Fenders For 14 Inch Wheels

Question

Question:

Do they come in 14

asked by: Clifton L

0

Expert Reply:

We do offer a couple of aluminum fenders designed to work with 14 inch wheels.

For a Jeep-Style design I recommend part # HP96VR. This is designed to work with 13 to 15 inch wheels, and measures 10 x 33 x 17 inches. The fender has a 1/2 inch lip on the radius. I have attached a product review video for this fender you can check out.

The other aluminum fender we carry that is designed to work with 14 inch wheels is part # CE17100ATB. This fender has the aluminum tread design and measures 32 x 10 x 16 inches.

expert reply by: Jeffrey L

0

Answer 1

Yes, the trailer fender part #CE17100ATB can be used on a trailer with 13 inch wheels. Basically we have wheel size suggestions for the fenders we carry but the best way to verify fit is to check the dimensions and make sure they'll fit. This…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 4

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 5

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 6

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 7

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 8

I am sorry I don't have any tires that are going to fit your rim. I do have a couple of comparable size tires that come in a wheel tire combo. I have listed the two below along with their lug patterns. 5 on 4-1/2 Lug Pattern - Kenda 205/65-10…

view full answer...

Answer 9

You can add larger wheels and tires to a trailer as long as you have enough room for the larger size. The main clearance issues we find when putting larger tires and wheels on a trailer is from the top of the tire to the fender and from the inside…

view full answer...

Answer 10

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

The closest radial tire size I would have to replace the 4.80-12 bias tire size is the Kenda Karrier S-Trail ST145R12 Radial Trailer Tire #AM10130. The 4.80-12 bias tire is 20.7 inches tall and 4.9 inches wide. The 145R12 radial tire is 21.3 inches…

view full answer...