Part Numbers: 90195,3070-P
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
The large buttons and colored LCD display on this proportional brake controller make it easy to see and easy to use. Store and customize your settings so you can easily swap out trailers and drivers and get towing.
Features:
Specs:
Braking output is the maximum amount of power that will be applied to your trailer's brakes. How much braking output you need is determined by the weight of your trailer; a heavier trailer will need more power to bring it to a stop. Use the arrow buttons on the front of the module to set the output. You want to set the braking output as high as you can without locking up the brakes. Once you've set up the brake controller the first time, you shouldn't need to adjust this setting unless the trailer load changes, you switch trailers, or road conditions change. The LCD display will show the current output setting being used.
The boost setting controls the aggressiveness of your trailer's braking, meaning how quickly the brakes reach the maximum braking level. You can adjust this when you're towing heavy loads and you need more umph to bring your trailer to a stop. Your tow vehicle doesn't need that much power to brake in time, but your heavy trailer does.
Depending on the level of boost, your trailer brakes can start at either 13 percent or 25 percent of the set braking output. What this means is that, instead of starting at 0, the brakes will start at 25 percent and get to100 percent sooner. This keeps the trailer from pushing your tow vehicle forward.
If your trailer weighs less than your tow vehicle, no boost is needed. But, if you want your trailer to lead the braking, you can select level B1.
Boost Levels:
| Approximate Gross Trailer Weight | Boost Level | Increase in Initial Power Output |
|---|---|---|
| Less than tow vehicle GVW | B1 | 13% |
| Equal to tow vehicle GVW | B1 or B2 | 13% or 25% |
| Up to 25% more than tow vehicle GVW | B2 or B3* | 25% |
| Up to 40% more than tow vehicle GVW | B3* | 25% |
*Both B2 and B3 offer a 25-percent boost in initial power. But the braking curve for B3 is more aggressive than that of B2. This means that, even though you will start out with the same intensity when using these boost levels, you will get an overall more aggressive braking experience with the higher level. So if you use B3, you will reach maximum braking sooner than if you use B2.
Storable Settings
Customize the P3 and store your settings so that you can easily access them later. If you tow multiple trailers, or the same one but with differing loads, store the desired boost and power levels for each so that you don't have to completely reset the controller every time you switch between trailers. It's easy to swap between drivers as well. Program the P3 display with your desired screen color, brightness, and language, and you can easily return it to your preferred settings the next time you tow.
The P3's LCD display features a distinctive look with multiple color and contrast options. With lots of customized options, you can change the display to make it easy for you to see and check your braking status at a glance.
It also includes comprehensible and detailed roadside diagnostics. The P3 advanced diagnostics not only notify you of potential problems, but they can also tell you where to begin troubleshooting.
Diagnostic troubleshooting displays include:
Diagnostic warning signs include:
Safety Features
The Prodigy P3 offers advanced safety features to prevent damage to various components of your towing setup. Integrated reverse battery protection shields the brake controller and your trailer's breakaway system from shorts. When the P3 is not in use, it will be in power-saving mode. In this setting, it draws only 3.6 milliamps, minimizing drain on your vehicle's battery.
The P3 also comes equipped with a hold feature to prevent wear on your brakes. When you're waiting at a red light, you don't need your trailer brakes on at full power. The longer you sit there, the more they will overheat. But with the P3, any time your tow vehicle and trailer are at a standstill with the brakes applied for more than 5 seconds, the hold feature will kick on and reduce power to just 25 percent. This will keep your trailer in place while saving your brakes.
The P3 keeps the manual override within easy reach, great for stopping sway or controlling your trailer's momentum in emergencies. To engage the manual override, just twist the rotary-style lever from right to left. This will activate the trailer's brakes and brake lights without you having to apply the brakes on your tow vehicle, perfect for limiting trailer movement while you're cruising.
The self-leveling feature of the P3 ensures that the brake controller continues to function even as you drive up steep hills or through the mountains. Simply mount it in your cab at any vertical angle, and the controller will level itself automatically thanks to its 360-degree rotational range. This makes the installation that much easier. But keep in mind that the P3 must be horizontally level and parallel with the direction of travel to work correctly.
Installation is a snap. After mounting the P3 unit in your cab using the included bracket, hardwire one end of the included pigtail harness directly into your vehicle. The other end plugs into the brake controller. To remove the P3 for storage when you're not using it, just unplug the unit and slide it out of the bracket. With a replacement wiring harness (sold separately) and replacement bracket (TK5906 - sold separately), you can even transfer the Prodigy P3 to another vehicle.
Installation Accessories
For even easier installation, a vehicle-specific specific wiring adapter is available for most newer trucks and SUVs. One end of the custom adapter plugs into your vehicle, and the other end plugs into the controller - no hardwiring required.
See also etrailer.com's exclusive 7- and 4-way brake-control installation kit (ETBC7 - sold separately) if you don't already have a 7-way plug at the back of your vehicle.
Note: If a custom brake control wiring adapter is not available for your vehicle, one of the following will be required:
20-Amp circuit breaker (9506P - sold separately) for 2- to 4-brake applications
30-Amp circuit breaker (38630 - sold separately) for 6- to 8-brake applications
The Tekonsha Prodigy P3 brake controller comes equipped with proportional braking to give you the best towing experience. Proportional braking means that your trailer brakes mimic your tow vehicle's brakes. If you slam on the brakes in your vehicle, your trailer brakes will activate with the same intensity; if you brake lightly, your trailer brakes lightly too. The trailer's braking is in proportion to your vehicle's braking. This saves wear and tear on the tires and the brakes on both your vehicle and trailer.
The Prodigy P3 uses an internal inertia sensor to detect how your vehicle is braking so it can send the right amount of braking power to your trailer. It measures the inertia of your tow vehicle and activates the trailer's brakes to slow at the same rate. The result is uniform braking across your towing setup. No push-pull action - just smooth, proportional braking every time.
California residents: click here
Install your electric brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in harness beneath your vehicle's dash.
Features:
This adapter plugs into the 4-pin connector on your vehicle's built-in brake control wiring harness. The harness is located underneath the dash, to the left of the steering column, taped to another harness near the emergency brake pedal.
To install your electric brake controller you need to connect the wiring of the controller to your vehicle. Certain manufacturers offer pre-wired options, typically known as tow packages, wherein these wires are run for you from the dash to the trailer connector on the back of your vehicle. Often, a brake controller wiring harness is included with your tow package. This harness plugs into a port beneath your dash and connects to the four wires of the brake controller. If, however, you have a brake controller with a plug in place of the four loose wires, you can use the Tekonsha adapter.
This adapter requires no hardwiring. It is designed to plug directly into your electric brake controller for the simplest installation possible. Because there are no wires to connect, installation is not permanent. You can unplug and remove your brake controller at any time and securely stow it away.
California residents: click here
Average Customer Rating: 4.9 out of 5 stars (6312 Customer Reviews)
The large buttons and colored LCD display on this proportional brake controller make it easy to see and easy to use. Store and customize your settings so you can easily swap out trailers and drivers and get towing. Install your electric brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in harness beneath your vehicle's dash.Perfect length and fit in my 2022 Honda Ridgeline. I carefully cut a hole at the back of the pocket just above the transmission controls, and with one end plugged into the truck, the other end was just long enough to plug into the controller before mounting it. I appreciate the nylon loom over the wires x a little extra protection when dragging the wires over metal brackets.
This was a very easy installation of the hitch, wiring harness and trailer brake. Less than 2 hours with some help from my wife. All of the electrical was plug-n-play. I'm sure doing it myself (with help from [online]) saved me a lot of money.
I have never used any other brand of brake controller so it's hard to compare brands. And since the Tekonsha controllers have always worked extremely well I've never had a reason to use a different brand. I use this on an F350 Powerstroke Diesel hauling an 18 foot enclosed trailer and a 12 foot dump trailer. I had one of these controllers destroyed (electronically) when my brother connected it via 7 pin to one of his trailers that was wired differently than my trailers. I replaced it about 10 years ago and haven't had a problem since. I also had my brother rewire his trailers to match mine in case he needed to borrow my truck again, which he has, with np problems. This last controller I purchased was for my tractor so I could move my trailers around safely with my 28hp tractor.
I love this! We camp monthly, and we tow our 23ft camper with a 1500 GMC. The break assist has been a fantastic tool to help keep us safe and in control of the camper.
This Tekonsha Prodigy P3 was recommended to be by a friend who works at an RV dealership service center. This is my fifth trailer brake controller over a forty-year period, and my first progressive controller. I really love this controller. My truck has a factory towing package, but was manufactured prior to inclusion of integrated controllers. Since the truck has factory towing, the installation was very simple. The installation instructions were clear and complete. I would definitely recommend this controller to anyone looking for a dependable, easy to install and easy to use controller.
I mounted my Tekonsha P3 on the dash just to the left of the steering wheel. Has very easy access to quickly activate the lever on the bottom of the unit to apply maximum trailer brakes. But I needed a wiring harness almost double the length of the Tekonsha Wiring Adapter so I just purchased two and spliced them together to make one long one......yea I could have saved money and just sliced in longer wires....Am very happy with the Tekonsha P3, With this mount it makes it easy to disconnect and put into my Ford F150 or my Tacoma.
Installed myself in about 30 minutes. 06 Silverado crew cab. Fit right up to factory fitting that was hidden up on top of the spare tire.
I have a 2012 Honda Pilot Touring. I needed to add an electric brake controller for my pop-up trailer. Based on the etrailer recommendation, I bought this wiring adapter and just hoped that it would work. Worked like a champ. It took me a moment or two to figure out where to plug it in on the Pilot, but once I did, it was trivial to make the connection.
The Tekonsha P3 and the wiring adapter have worked great for us. Installed in a Subaru Ascent on the bottom left side of the dash. Worried about hitting it with my foot, but that hasn't even been close to an issue. We leave it installed full time and I never think about it. Actually, as a break controller, that's a great thing. We adjusted the settings a couple times during our first outing with a trailer and have never touched it since. It truly does the proportional breaking well. I definitely prefer the physical box and not having to futz with an app.
Tekonsha P3 brake controller was easy to install. Stacey got me the right wire adapter f ou r my 2022 Frontier. Basically Plug and Play install.
eTrailer customer service agent (Bailey) is very knowledgeable and been a tremendous help in ordering the correct brake controller!
Charles
3/11/2024
After 1 year and over 13,000 miles??? Excellent!!!
I installed this in my 1987 K5 Blazer hauling a trailer with an old mustang on it from Washington state to south california… never had an issue. I watched a few YouTube videos and followed the instructions, took me a little more than half a day but this was because i had to replace a fair amount of old wire and then loom it all correctly to look professional but to also have a lasting result. I was concerned I did something wrong as the device stays on with the back light a few minutes after turning off the vehicle… it’s normal, just how the device works. The controller is way to use otherwise. It does brake controller things.
Ordered 9 Jan 2023 and received today 31 Jan 2023. Seemed to sit in US mail system for quite awhile. Once received in Quebec Canada and cleared Canada Customs I received it in 3 days. I am replacing my brake controller with a new one and wanted to upgrade to a better one. Tekonsha P3 comes highly recommended and install is pretty straight forward. I haven't put this to the test as yet but I do not anticipate any problems. Only issue is in shipping.
The Prodigy P3 came on just as the instructions said it would. Although I have not used it yet it looks good in my ‘15 LX. I look forward to great service towing my 20’ flat trailer with tractor, rotary cutter and box blade. My to the staff at etrailer.
First, a huge "Thank You" to Janice!!! You are the best, and the main reason I am the proud owner of Tekonsha P3 Brake Controller! (see, I initially had an issue with my standard online payment service and almost canceled my order because of it) So I went old school and picked up the phone, one with a cord and spoke to a human being. Her name is Janice, and she made me feel confident that I could trust her and etrailer. And as a result, 4 days after placing my order with her I received my package. That's incredible. I am very happy and will most certainly do business with etrailer again in the future because of Janice.
I don't have any experience with brake controllers. So I can't really comment on how much better or worse this one is to any others. But since I am new to the B/C scene maybe this can be considered an unbiased, non professional review of the Tekonsha P3.
My general skill level is "requires supervision around all power tools". But I do have some mechanical ability (snicker). So I will just say, if I could install this thing anyone should be able to do it. Of course I also bought the OEM wiring harness for my vehicle so even I was able to figure out which plug went where. On A scale of 1 to 10 I give it a 3 (I'm somewhat large and getting under the dash wasn't easy or it would be a 1). And as others have said, deciding where to mount it actually took longer.
I attached mine to the top of the lower dash cowl and it fits almost tight to the dash but still within the 180 degree limit. This positions the controller at the same height as my knee and puts it within fingertip reach while resting my hand on my knee. I can see the controller perfectly through the steering wheel spokes. I went with the green screen background. it seemed to provide the best view in all lighting conditions.
The controller itself works perfectly and the set-up was a breeze. Once installed all the functions worked as described. The real time vehicle diagnostics are a plus. I like being able to monitor my battery voltage to the decimal place if I want to. I'm sort of a techno geek so this is really cool. I set the B/C voltage per the instructions and will only use the boost feature if I am in a hurry or feel the trailer is at max load, but my truck is 8k lbs so you may want to set yours to suit your own conditions.
I highly recommend the Tekonsha P3 brake Controller if you want the latest and probably the best controller out there in this price range. I highly recommend the OEM wiring harness if your skills are not pit crew comprable and want the easiest install possible. And, I highly recommend you buy it from etrailer if you want to get it at the best price available (I checked them all) and want the added security you're buying from one of the best online retailers that sells this product. And do yourself a favor, go old school for a change, use the phone and call them, and ask for Janice, although I'm willing to bet everyone there is as nice as her.
Rob
Installed this on my GMC 3500 Duramax with factory integrated brake controller. Not happy with the integrated brake controller on my truck, had problems from the start on 3 different occasions with "Service Trailer Brake" warning on DIC, which of course means NO TRAILER BRAKES. Decided the P3 was the perfect solution. Many more features than the IBC, plus the P3 will also work with electric over hydraulic disc brakes should we ever need that in the future. Fairly easy install on this particular truck, the most difficult thing was running the brake wire from the controller to the 7-pin plug. (This is only required when installing in a vehicle with a factory installed brake control) Well worth the extra effort.
10/10 does the job very well and was easy to install myself (be careful about airbags). Saved me a large custom job bill. Worth the price and functions perfectly.
I purchased with the connecting cord/plug for my vehicle and it was seriously the easiest thing to install. Two plugs ins, screwed into my lower dash and done.
I had to build a custom bracket for the controller mount since the X is limited in under dash metal but the install went well. The 7 pin trailer harness is a factory Nissan part (plug and play) , but since the receiver does not have the any mounting brackets, I positioned the 7 pin connector up and out of the way of harm by drilling and flush mounting it in the rear bumper. Thanks for carrying products relevant to your customer's needs and having products that work right. I have attached some pics from the finished install. I will be ordering accessories as I need them from your company as you have always been prompt, thorough and very courteous in all of your correspondence.
Installed P3 this weekend in 2013 Tundra Crewmax with towing package and pre-wire. Extremely easy, even with the center console installation. Will let the photos tell the story. Did have to combine the P3 included harness with the additional OEM harness to gain the length I needed. Plug and play with the pre-wire. Hooked up to trailer and set boost levels for varying loads. Works great! Vast improvement over older model Tekonsha controller in my Ram 2500 Diesel. Pull a Kiefer BP horse trailer: about 3600 lbs empty, 7500 with 3 quarter horses and gear. Usually pull 6-8 times per year, with only 1-2 horses. Short distance and flat terrain. It took about an hour to install. Dad is a retired USAF/FAA radar technician with every tool known to man. He QC'd the job. Will try to write better review later.
I have a 2018 BMW X2 that did not come with a factory tow package. I had an etrailer hitch and 4 way plug installed last year and has been perfect since. I just recently purchased a camper and needed to have a Brake controller & Brake controller 7 way deluxe kit installed. My mechanic installed them with the detailed instructions that the units came with without any issues. The Tekonsha P3 is extremely user friendly and is working flawlessly. A bit overkill for my car being I can only tow max 3500 pounds, and my camper is 1 axel. this unit is rated up to 3 axles. I look at it like this way, when I trade in my BMW I will take my P3 with me. etrailer is amazing with the support & products they provide and I highly recommend them to anyone who asks me.
Hi, I got my Item: 90195 and shipping was fast. I was able to get the break controller installed in my 2012 Cadillac Escalade Luxury using the etrailer.com video guide for a 2009 Cadillac Escalade. The install and wiring was the exact same as the video however my wires under the dash or wire bundle did not have a wiring sticker. The color of the wires were the same as in the video. This etrailer video is great and I used it to get my controller installed in about 1.5 hours. My install was trouble free.
This weekend I was able to test out the my new P3 90195 controller and get it calibrated with my 29 foot travel trailer this weekend. Used a B2 setting with 8.0 power. The user guide and instructions you get with the controller help you know what settings to use and how to set the power level.
This is my second controller as I got a P2 Tekonsha from etrailer about 4-5 years back and installed it in a 2007 trail blazer. This older 2P break controller is still working great. I have been rather happy with the quality of the Tekonsha controllers I have. I have not had to call etrailer for support or install questions but did receive a few emails from them to check in with me to ensure I got my shipment and offer me help. They do a good job supporting and responding to their customers and provide an A+ customer experience.
We found this product through a search for info on how to install a brake controller on our 2017 Honda Ridgeline. We had a Draw-Tite Activator IV Controller but struggled to hook it up until we watched your online video and discovered the existence of this Tekonsha adapter (3070-P) which was literally plug and play. We chose to install our controller in the same location as in the video but did not want to cut a hole in the panel. The wires tucked easily out of the way without cutting the hole. We towed yesterday and the trailer brakes/controller worked perfectly. Never could have done this without your video and this adapter. The picture shows our controller installed. You can’t really see the adapter since much of it is tucked under the dash.
Peggy C.
10/14/2020
One year later we are still towing with a perfectly working brake controller thanks to this plug and play adapter! No issues!
I purchased and installed the P3 controller in a 2018 Toyota Highlander XLE after reading many great reviews about it. Wanted a hard wired controller vs. wireless because a brake controller is too important to run over an unreliable wireless connection. Having an IT background I know how unpredictable wireless connections can be. Installation was fairly easy, the hardest part was running a few wires through the firewall of the vehicle.
A few notes, the installation of the actual controller under the steering wheel area was a little difficult because of the design of the mounting bracket. This could be designed better for easier installation. Also, I got a pre-collision warning on my instrument cluster whenever the brake controller was activated. To fix this I had to solder a 1 amp diode on the red cable, which I protected with heat shrink. I reached out to tech support about this error and they were very helpful talking me through a solution.
I like the adjustment capabilities of the controller. I have been able to adjust it so the brakes don't grab when stopping slowly. I really like the manual slide for activating the brakes. This has been very useful for applying brakes on the trailer in a few critical braking moments. The manual lever is also very useful for checking the brakes after connecting the trailer to make sure they are working correctly. I also like that the display shows the level of braking that's applied to the trailer. The color of the back-lit display can also be adjusted to match the vehicle's displays. I definitely recommend this brake controller.
We have a Honda Ridgeline and this part plugged into the factory plug that was under the dash by the emergency brake petal switch. It was difficult to get to, but success was achieved. This was needed for our camper trailer. This made it easy, no hard wiring, just ordered the part for the Ridgeline and then plug and go. The brake controller plugged into the other end and now I am a happy camper. It worked, I blew a fuse while installing, must have touched something? No problem though, replaced it and was all was good.
Jim A.
6/8/2016
After one year, it is nice to not even think about it. I love products that work correctly. Gives one peace of mind. This is a great product. . thanks etrailer and Tekonsha for being wonderful companies. . . jim
I was in the market for a controller for my 2011 Jeep Grand Cherokee and this was a great controller and the price from etrailer was very competitive with other sites. What ended-up being the deciding factor for me on where to purchase the controller was the ease-of-use of the etrailer site. They made it simple to find and compare controllers and getting the correct wiring harness for my application was easy.
In addition to the site they have outstanding customer service. The controller was shipped the day after I ordered it (on a Saturday no less) with free upgraded shipping. They even followed-up with me once the controller arrived at my house. I wish all sites had this level of customer service!
Ask the Experts about this Trailer Brake Controller
Do you have a question about this Trailer Brake Controller?
Info for these parts were:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Jacques
4/11/2023
Perfect. I tow a heavy trailer only a few times a year, and every time I do, the controller works as I expect. The controls are simple enough that I do not have to review instructions to bump the power up or down to match the trailer weight.