If you wanted to install E-track like the # EM59150 directly to a wood floor using wood screws you could but you'd want to put a screw in each mounting hole like you mentioned. This attachment method would easily allow the track to have it's full capacity of 2,000 lbs. view full answer...
You will need to use a wiring harness with a converter to convert your vehicles 3 wire system to the trailers 2 wire system. We have a kit available for you to use. The 4-Pole Hardwire Kit with Converter (Includes Tester), item # 119178KIT is wired behind each of the vehicle taillights and provides a 4-Way connector for towing. You will need to use the included circuit tester to find the left turn, tail light and brake light circuit behind the left side tail light assembly and connect the... view full answer...
We do have a couple of different options for bumpers that fit your 1997 Nissan pickup, both of which are from Westin and both of which come with mounting brackets. They are also available in your choice of either chrome or black.
- Westin Fey Diamondstep Rear Bumper with Custom Installation Kit - Black # 66000-95300 or Chrome # 76000-95300
- Westin Fey Surestep Rear Bumper with Custom Installation Kit - Black # 66001-95300 or Chrome # 76001-95300
These are very similar step bumpers... view full answer...
If you have the mid-year 1986.5 Nissan Hardbody that has the two large headlights rather than the four smaller lights on the older model, you can use the Hopkins Plug-in Simple Wiring Harness, part # HM43505, to install a 4-Way at the rear of your vehicle.
The # HM43505 wiring harness will plug into the back of your vehicle's taillights. I am including a link to the installation instructions on the # HM43505 wiring harness.
If your vehicle is not the 1986.5 or newer model, you will need... view full answer...
The Hopkins Vehicle Wiring Harness, # HM43505, is for the Nissan if it were towing a trailer and needed to power the trailer lights. Instead, there are a couple of different options for when you are towing the Nissan and need lights.
Since you mentioned that you wanted to power the Nissan lights, you will want to use a diode kit, # RM-154. Installing this kit will put the turn signals and brake lights on the same bulb and the running lights will be on a separate bulb. If you want the turn... view full answer...
As replacement tarps are very specific as to what they will fit, we do not list the dimensions. However, to get the BlackMax tonneau cover replaced on your 1996 Nissan Frontier pickup with the short bed, we do have what you need. I do need to mention that the correct one will depend on if you have the King Cab or the Regular Cab, but I do have both options listed below.
King Cab:
Replacement Tarp for Extang BlackMax Soft Tonneau Cover - Black # EX1865
Regular Cab:
Replacement Tarp for... view full answer...
It sounds like your 1986 Nissan Pickup was built in the first half of that model year life cycle. The harness for the 1986 , # C55353 has a converter and is for 1986.5 mid-year models. If your truck does not have separate turn signals and brake lights then this harness will work.
You would have to hardware in harness # 18252. I have linked a video that shows how you will need to test the wires, either at that round plug you mentioned or behind each tail light to wire in the harness. This... view full answer...
It looks like you're looking for a budget-friendly tonneau cover for your 1997 Nissan short bed pickup. We do offer some great options, but the # TPLR-3095 you'd asked about is a fit for a later model Ford Super Duty short bed, so it wouldn't fit your truck.
For your regular cab truck, I'd recommend the Truxedo TruXsport, part # TX273101 which is a roll up tonneau like the one you'd looked at.
I recommended one of these covers to a buddy of mine who purchased it a couple of months ago,... view full answer...
We have replacement legs for the HappiJack truck camper systems like the part # LC736515 which has 36-1/2 inches of lift and a 2,800 lb capacity as well as the # LC736514 which has 34-1/2 inches of lift and a 2,200 lb capacity but the legs themselves do not have rebuild kits available. view full answer...
The Westin Replacement License Plate Light Kit for Westin Bumpers # 00007153 is made to work with specific Westin aftermarket bumper products, those in their Diamondstep, Surestep or Perfect Match series. It works with all Diamondstep and Surestep bumpers and the Perfect Match bumpers 31000, 31001 and 32000.
The linked page shows all four currently-available Westin bumpers that fit your 1996 Nissan pickup, parts # 66001-95300, # 66000-95300, # 76000-95300, and # 76001-95300.
All of these... view full answer...
A ground problem is a possibility but having an insufficient ground connection usually causes the trailer lamps to behave erratically, or to work properly until the vehicle headlights are switched on.
The best place to start would be to use a circuit tester like part # PTW2993 and test the trailer connector as each function is tested. This will tell you if the problem exists on the vehicle or the trailer.
If your testing shows that the trailer connector is functioning properly, then... view full answer...
To answer the second question first, the lights are submersible meaning water can drain out. You will want to seal up the electrical connections as best as possible. Heat shrink tubing works well. You can also coat them in liquid electrical tape, # SWC50122.
For the side marker lights you would splice the power wire into the running light wire using a quick splice connector. Because this is a wishbone harness (it has 2 running light wires, one for each side) you would really only need... view full answer...
I do have a solution for you but you will not be able to use a rear mount hitch on the front of a vehicle. Some trailer hitch manufacturers we carry do not give us the hitch dimensions because it is proprietary information.
But I can tell you that the hitches you have listed are not going to fit at the front of your 1996 Nissan pickup. The frame is narrower at the front but beyond that it would require modification to the hitch and/or the vehicle that would void the hitch warranty and... view full answer...
In regards to fans, it is not the size that matters it is the airflow. Electric fans are not necessarily vehicle specific. If you have # D16908 that you have referenced, it puts out 450 cubic feet of air per minute. This is not very much and a fan that can generate more would be needed.
Typically, a 6 cylinder motor requires 1,600 to 2,000 cubic feet per minute.
The fans that you could use largely depends on the space you have in the engine compartment to mount them. I recommend getting... view full answer...
If you are replacing the White ground wire on your 7-way trailer connector you can use 12 gauge wire like part # 12-1-1. This is Black wire but will work for replacing the White wire you said you have.
For your 1993 Nissan pickup truck I recommend first installing a 4-way trailer connector like part # HM43505. This is a simple installation. You just plug the harness into the truck wiring located behind the driver and passenger tail lights. I have attached a drawing that shows how this... view full answer...
Yes, the spindles of the Dexter Trailer Idler Axle Beam # T20BTR-EZ-6048 are EZ lube spindles so it comes with the zerk fitting installed already. view full answer...
There is not a video of an installation on that particular vehicle. I did reach out to my contact at Curt to confirm that the correct hitch fit is # C13092. I've attached the installation details to assist with the installation. The Curt wiring harness # C55353 is also a confirmed fit and will give you the trailer connection needed for towing.
I've attached an article on ball mount fit, so you can determine what you need for the proper fit. I've also linked the page to your options. view full answer...
The Hopkins 4-pole wiring harness made for your 1996 Nissan Pickup is kit # HM43505 which appears on the linked page along with similar item # C55353 from Curt. All of these wiring kits use custom-fit plugs for simple installation at the truck's taillight connectors. No splicing is required for these custom kits.
The Hopkins hardwired harness # HM48895 is made for newer vehicles that use LED lights. This item has a red wire that splices to a vehicle's brake light wire and these signals... view full answer...
Yes, we do have a T-connector style trailer wiring harness for the 1996 Nissan pickup. You will need to use # HM43505. I have included a link to the installation instructions for you. view full answer...
Go To Results