Expert Answers about Nissan Pickup
- Solution for HappiJac Truck Camper Jack That Needs Rebuilt
- We have replacement legs for the HappiJack truck camper systems like the part # LC736515 which has 36-1/2 inches of lift and a 2,800 lb capacity as well as the # LC736514 which has 34-1/2 inches of lift and a 2,200 lb capacity but the legs themselves do not have rebuild kits available.
view full answer... - Recommended Tonneau Cover for 1997 Nissan Short Bed Pickup
- It looks like you're looking for a budget-friendly tonneau cover for your 1997 Nissan short bed pickup. We do offer some great options, but the # TPLR-3095 you'd asked about is a fit for a later model Ford Super Duty short bed, so it wouldn't fit your truck.
For your regular cab truck, I'd recommend the Truxedo TruXsport, part # TX273101 which is a roll up tonneau like the one you'd looked at.
I recommended one of these covers to a buddy of mine who purchased it a couple of months ago,...
view full answer... - Solution for Wanting Only a Rear Ladder Rack Upright for a Truck
- I think I have a better solution for you as long as you have a hitch installed on your vehicle, but the # DZ951600 that you referenced isn't sold individually.
Instead I would recommend the Rhino-Rack T-Load # RTL002. This will install in a rear mounted hitch and will provide a crossbar at the rear of your vehicle like you said you were interested in.
If you are in need of a hitch for your 1986 Nissan Truck you would want the part # 75186.
view full answer... - Trailer Wiring Harness for First Half 1986 Model Year Nissan Pickup Trucks
- It sounds like your 1986 Nissan Pickup was built in the first half of that model year life cycle. The harness for the 1986 , # C55353 has a converter and is for 1986.5 mid-year models. If your truck does not have separate turn signals and brake lights then this harness will work.
You would have to hardware in harness # 18252. I have linked a video that shows how you will need to test the wires, either at that round plug you mentioned or behind each tail light to wire in the harness. This...
view full answer... - Troubleshooting Trailer Wiring that Doesnt Function After Install on 1987 Nissan Truck
- First thing you should do at this point is test the 4-way of the wiring harness with a circuit tester part # PTW2993 for voltage on all of the right pins when the taillight signals are being applied. Just like in the video I attached.
If the voltage checks out there but the trailer lights still don't function right then the problem is on the trailer wiring. That would mean that problem is either due to a ground issue or a short issue.
Make sure that the trailer side connector is clean...
view full answer... - How to Protect Bulldog Winch Quick Connectors for Winch Wiring on a Truck
- The Bulldog Winch quick connectors # BDW20047 themselves do not have any sort of cover to protect them from the elements. But what you could do is modify mounting box # RP74641 and that will help protect them.
There is no one place that you have to mount the connectors. You can mount them in a place that works best for you.
We do sell 10 gauge wire. I recommend # 10-2-1 since it is 2 wires in 1 sheath. It is sold by the foot so if you needed 20 feet you would put 20 in the quantity box.
view full answer... - Curt Hitch that Fits 1997 Nissan Pickup
- The Curt hitch # C13092 does fit your 1997 Nissan truck and does require drilling to install. For more info on the install check out the install instructions link I attached.
view full answer... - Trailer Wiring Recommendation for 1997 Nissan Pickup
- With a 4-way flat trailer wiring harness like the # HM43505 which is a fit for your 1997 Nissan Pickup the only functions you get are the turn signals/stop lights and running light circuit.
If there's an additional circuit needed like maybe a 12 volt power circuit you'll need the 4-way to 7-way adapter part # 37185. You'll then need to connect the black wire of this to the positive battery terminal through a breaker like part # 9510.
view full answer... - Replacement License Plate Light Kit Recommendation for a Westin Surestep Bumper
- The correct replacement license plate light kit for your Westin Surestep Bumper is the Replacement License Plate Light Kit # 00007153
view full answer... - Parts Needed to Flat Tow a 1995 Nissan Pickup
- To flat tow a vehicle you need 5 primary items, Base Plates, Tow Bar, Safety Chains/Cables, Supplemental Braking and a Wiring Solution that provides indicator lights on the vehicle in tow to match that of the RV. The Roadmaster Crossbar-Style Base Plate Kit, # 317-2 that you identified is a confirmed fit for the 1995 Nissan Pickup and a great choice. This is a crossbar-style base plate and the Roadmaster Falcon All Terrain, Non-Binding Tow Bar, # RM-522 will fit very well for with these...
view full answer... - Trailer Wiring Harness Recommendation for a 1993 Nissan Pickup Truck
- We currently do not have videos for the trailer wiring harnesses for the 1993 Nissan Pickup trucks. But I have included a link to the installation instructions to the right for harness # HM43505 which is the harness that I recommend.
view full answer... - Recommended Parts Needed To Install 7-Way Trailer Harness On 1993 Nissan Pickup
- If you are replacing the White ground wire on your 7-way trailer connector you can use 12 gauge wire like part # 12-1-1. This is Black wire but will work for replacing the White wire you said you have.
For your 1993 Nissan pickup truck I recommend first installing a 4-way trailer connector like part # HM43505. This is a simple installation. You just plug the harness into the truck wiring located behind the driver and passenger tail lights. I have attached a drawing that shows how this...
view full answer... - Can E-Track Attach Directly to Wood Floor with Wood Screws
- If you wanted to install E-track like the # EM59150 directly to a wood floor using wood screws you could but you'd want to put a screw in each mounting hole like you mentioned. This attachment method would easily allow the track to have it's full capacity of 2,000 lbs.
view full answer... - Recommended Front Mount Hitch for 1994 Nissan 4x4 Pickup
- There is no front mount hitch receiver available for the 1994 Nissan pickup. However, we do offer several rear mount hitch receivers that are confirmed fits. I have included a page that lists all of the rear mount trailer hitches that are confirmed fits for your vehicle.
If a rear-mount receiver can meet your requirements please let me know and I will be glad to make recommendations for the required related components to fit it based on your specific application.
view full answer... - Does Detail K2 Summit Plow Fit 1987 Nissan Truck without Modification
- The K2 plow setup you referenced for your 1987 Nissan Pickup plow K2SUMM8826 and # K286610 is a confirmed no-drill, no-weld option that would work great. It bolts on.
It bolt directly to the frame and you'd be good.
view full answer... - Will Hopkins Trailer Wiring Harness for 1995 Nissan Pickup Work with LED and Non-LED Taillights
- The Hopkins Vehicle Wiring Harness # HM43505 that you referenced is a confirmed fit for your 1995 Nissan Pickup and will work great to power trailer taillights that are either LED or incandescent.
view full answer... - Does Dexter Trailer Idler Axle Beam # T20BTR-EZ-6048 Come with Grease Fittings Installed
- Yes, the spindles of the Dexter Trailer Idler Axle Beam # T20BTR-EZ-6048 are EZ lube spindles so it comes with the zerk fitting installed already.
view full answer... - Recommendations for an Electric Radiator Fan for a 1984 Datsun 720 2.4L V6
- In regards to fans, it is not the size that matters it is the airflow. Electric fans are not necessarily vehicle specific. If you have # D16908 that you have referenced, it puts out 450 cubic feet of air per minute. This is not very much and a fan that can generate more would be needed.
Typically, a 6 cylinder motor requires 1,600 to 2,000 cubic feet per minute.
The fans that you could use largely depends on the space you have in the engine compartment to mount them. I recommend getting...
view full answer... - Mounting Kit Recommendation for Fitting K2 Rampage II Plow # K2RAMP8219 to 1992 Nissan Pickup
- For your 1992 Nissan Pickup the install kit you need to install the K2 Rampage II Plow # K2RAMP8219 is the part # K286610 and you'd be set.
view full answer... - Recommended Trailer Hitch Receiver and Wiring for 1996 Nissan Pickup
- There is not a video of an installation on that particular vehicle. I did reach out to my contact at Curt to confirm that the correct hitch fit is # C13092. I've attached the installation details to assist with the installation. The Curt wiring harness # C55353 is also a confirmed fit and will give you the trailer connection needed for towing.
I've attached an article on ball mount fit, so you can determine what you need for the proper fit. I've also linked the page to your options.
view full answer...
Go To Results