Expert Answers about Infiniti
- Delay From HydraStar Marine Electric Over Hydraulic Actuator HBA16 When Braking
- I did not see where you mentioned what electric over hydraulic actuator you are using but if it is the HydraStar Marine Electric Over Hydraulic Actuator part # HBA16 that you referenced then the first thing I recommend you check is that you are using the correct EOH setting on your brake controller. If this is confirmed I would then bleed the brakes which can be done using the attached photo.
If you still have issues with delays after you have done the above then please just let me know...
view full answer... - Exhaust Pipes Seem to Hang Lower After Curt Hitch Installation on 2016 Infiniti QX 50
- According to Curt, when installing the Curt Hitch, # C11510 on a 2016 Infiniti QX50, you have to invert the rubber isolators for the exhaust system when reconnecting the exhaust mount to the hitch.
If you failed to invert these rubber isolators, then it is possible that you vehicle's exhaust pipes might very well hang lower than they originally were mounted. Maybe as much as an 1-1/2 inch lower.
I would double check or even invert theses hangers then reinstall the exhaust to see if this...
view full answer... - Recommended Trailer Wiring Harness for 2013 Infiniti JX35
- The Tekonsha T-One Vehicle Wiring Harness # 118670 that you recently installed is actually not a fit for your 2013 Infiniti JX35. The harness will physically install just fine, as you found, but the JX35 is missing an additional factory jumper harness that is needed to activate the turn and stop light signals. This explains why you aren't getting these signals to work on the connector.
The only available wiring harnesses that are confirmed to work on your 2013 Infiniti JX35 are universal...
view full answer... - No Lights on T-One Vehicle Wiring Harness for 2015 Infiniti QX60
- The T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # 118670 which is a fit for a 2015 Infiniti QX60 is a plug-in-play harness so there isn't much to troubleshoot. The relay harness installs behind the rear, driver side interior cargo panel and the trailer connector harness installs under the rear bumper on the passenger side. There are three relay that install on the harness and two which get installed in the engine bay fuse box. I recommend making sure the harnesses...
view full answer... - Troubleshooting Left Side Tail Light Not Working on Trailer With 2017 Infiniti QX60
- The blinking on the # I26 is actually correct. It doesn't make sense that the right turn signal blinks on the left and the left blinks to the right of the right turn signal light (it even sounds confusing) but that is how it's designed. You can see this in our review video below.
Based on the fact that this is working correctly it could still be the trailer side. Take a circuit tester like the # PTW2993 and check to see if you have power right behind the trailer side connector. If you...
view full answer... - Troubleshooting Trailer Lights Not Working with T-One Wiring Installed on 2020 Infiniti QX60
- Thank you for all of the information!
The T-One Vehicle Wiring Harnesses, like part # 118670 for your 2020 Infiniti QX60, typically do a great job and don't malfunction often. Since you've replaced this harness already and you've checked and found your fuses to be good there is really only one other thing on the vehicle end that could be the problem and that's the OEM wiring on your vehicle (it's possible both T-One harnesses were bad but REALLY unlikely). What you'll do to test this is...
view full answer... - How to Install Straps on the Saris Bones EX 2 # SAR83FR on a 2019 Infiniti QX60
- Looking at the vehicle you entered in the fitguide, it looks like you have a 2019 Infiniti QX60. In order to install the Saris Bones EX 2 # SAR83FR properly on your vehicle, I confirmed with Saris that you need the hatch huggers # SA3035 to replace the upper straps. For the lower straps, you can either use the hatch huggers # SA3035 or place the hooks inside the trunk.
I went ahead and attached a video that shows how the hatch huggers work.
view full answer... - Brake Controller Stopped Working with Brake Pedal on a 2010 Infiniti QX56
- When there is no power to the red wire on a brake controller that plugs into a vehicle then the likely culprit is a blown stop light or CHMSL (center high mount stop light) fuse. If the brake controller is hardwired to the vehicle then check the wire to which the red brake controller wire is connected.
If that wire has power but the brake controller red wire does not then you will need to make a new connection. If the wire does NOT have power then it goes back to a blown stop light or...
view full answer... - Rear Brake(s) on Trailer Get Hot Once in a While
- I am assuming you have electric brakes? If so there could be a number of reasons why the rear brake(s) on your trailer are getting hot. These reasons include but are not limited to lack of lubrication, spindle nut too tight, improper adjustment, failing brake magnets etc. However, since the issue only occurs every so often then it sounds like you have a wiring/magnet issue.
I recommend checking all the wiring and making sure there is not any power on the brake output wire once the brakes...
view full answer... - Hitch Installed on 2016 Infiniti QX60 Rattling on Exhaust
- What you describe is a fairly common occurrence. Because the # C11510 hitch mounts to fixed mounting points on your 2016 Infiniti QX50, that hitch is going to sit in the same exact spot on every US Market 2016 Infiniti QX50. However, because the exhaust system uses flexible rubber isolators and easily bendable exhaust hangers, the precise location of the exhaust pipe where it runs next to the hitch can vary from vehicle to vehicle, sometimes by an inch or more. Typically, fixing the problem...
view full answer... - Troubleshooting Wiring Harness Installation for 2013 Infiniti JX35
- We are happy to help with getting you the correct parts for your vehicle.
For your 2013 Infinity JX35, the Curt wiring harness # C56281 you referenced is the correct fit for a factory replacement. The relays you need to install are not in the 6x6 fuse box according to my tech contact but rather in the small box by the firewall that is about 1-1/2 by 6 inches and has a black cover you will remove. It unfortunately is not quite as easy to get to and you may want to test the harness to...
view full answer... - Troubleshooting Sparks on Safety Chains When Connecting to Hitch
- What you've been told is likely the culprit, and I don't believe that it's coming from an issue on the Curt # C56357 you've installed. I would check the ground wire on the trailer wiring harness to make sure that it is connected to a paint, rust and debris free spot on the trailer frame. This is the most likely cause of the sparks that you're seeing. If you can check this and see if it continues, that's a good place to start. If you're still experiencing the same issue after cleaning off...
view full answer... - Troubleshooting Prodigy P3 Brake Controller Random Error Codes
- It sounds like either your Prodigy P3 # 90195 wiring needs to be looked at, or the wiring for the trailer brake circuit.
Start off by checking that the wiring for the P3 is operating as it should. The pigtail connected to the back of the controller will have the following wires connected to the following functions:
Blue - 7-Way Output to Trailer
Black - 12V Power
White - Ground
Red - COLD Side of Stop Light Switch (only gets hot when brake pedal is pressed)
If all of that checks out...
view full answer...
Go To Results