Recommended Trailer Wiring Harness for 2013 Infiniti JX35
Question:
2013 infiniti jx35 lights not working from four pin trailer harness bought t-one plug and go wiring harness after all hooked up only light from four pin is headlight, no signals and cant tell if brake light is working, using a test light. used video from 2014 infiniti qx60 which showed exact hookups in rear of car only difference is fuse box under hood is not in same place. nothing was said about using a converter. I went this route after talking with an infiniti tech person down in the twin cities area
asked by: Brian C
Expert Reply:
The Tekonsha T-One Vehicle Wiring Harness # 118670 that you recently installed is actually not a fit for your 2013 Infiniti JX35. The harness will physically install just fine, as you found, but the JX35 is missing an additional factory jumper harness that is needed to activate the turn and stop light signals. This explains why you aren't getting these signals to work on the connector.
The only available wiring harnesses that are confirmed to work on your 2013 Infiniti JX35 are universal kits like the Curt Powered Tail Light Converter Kit # C56190KIT. This kit will let you splice into the factory wiring on your vehicle to provide you with a fully functional 4-Way connector. I have attached an installation video on your 2013 JX35 that you can use for reference.
Products Referenced in This Question
Curt Powered Tail Light Converter w/ 4-Way Flat Trailer Connector and Install Kit
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Converter
- Universal Fit
- 4 Flat
- CURT
more information >
Product Page this Question was Asked From
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Options to Install a Brake Controller and Trailer Hitch on a 2013 Infiniti JX35
- Shop: Trailer Wiring
- Shop: Brake Controller
- Shop: Trailer Hitch
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Search Results: 119190kit
- Search Results: 76031
- Search Results: 7894
- Search Results: rm~061
- Video: Trailer Hitch Installation - 2013 Infiniti JX35 - Draw-Tite
- Video: Trailer Brake Controller Installation - 2013 Infiniti JX35
- Shop: Towing Mirrors
- Q&A: Parts Needed to Install 7-Way Trailer Wiring on 2013 Infiniti JX35
- Q&A: Best Trailer Wiring Harness for Towing Small Trailers with 2016 Infiniti QX60
- Q&A: What Vehicles Does Draw Tite Hitch # 76031 Fit
- Q&A: Is There a Photo of Hitch Receiver 76031 Installed on a 2013 Infiniti JX35
- Q&A: 4-Way Trailer Wiring Harness Recommendation for 2013 Infinitiy JX35
- Q&A: Locking Hitch Pin Recommendation For 2 Inch Trailer Hitch
- Search Results: etbc7
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Shop: Pigtail Wiring Harness for Tekonsha and Draw-Tite Brake Controllers - 34" Long
- Shop: Curt LED 4-Way Flat Connector (Vehicle End) Tester
- Shop: Brophy Stabilizer Clamp and U-Bolt for 2" Hitch Receiver - Black Powder Coated Steel
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Shop: InfiniteRule Hitch Lock for 2" Hitches - 2-5/8" Span - Stainless Steel
- Video: TruRyde Electric Brake Assembly Installation
- Video: etrailer Electric Trailer Brake Kit Review and Installation