3-3/8" Diameter round. Waterproof, LED trailer light with reflex reflector serves as a side marker light or a clearance light. Recessed mount with flange. Locking clip minimizes vibration. Accepts 2-prong PL-10 plug. 1 Diode. P2 rated.
Features:
Specs:
The waterproof construction of this light makes it ideal for use on trailers that may be submerged, like a boat trailer. The housing and lens are sonically sealed together to create a single unit, which means that water will not get into the light and damage the diodes or circuit board.
A P2-rated light produces a 45-degree angle of light to either side of its centerline for a total of 90 degrees of coverage. This beam pattern can be seen straight on, but it cannot be seen clearly from the side. So this type of light can be used as either a side marker light or a clearance light, but it cannot function as both. If you need both functions, then you must install 2 separate lights on your trailer - one as a front or rear clearance light and one as a side marker light.
This light has an industry-standard PL-10 connection as pictured above. The light accepts a 2-prong plug (sold separately).
Recessed-mount trailer lights install underneath a housing or a grommet, which is often sold separately. These lights will extend into the mounting surface and require that a hole be cut into your trailer.
California residents: click here
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Speaker 1: Today, we're taking a look at the Optronics Amber LED Clearance or Side Marker Light. This round trailer light serves as either a side marker light or a clearance light for your trailer. It features the built-in reflex reflector, which eliminates the need for a separate reflector and it also features durable surface mount technology when it comes to the construction of the LED circuit board. That design is designed really to better withstand shock and vibration and allow for improved heat distribution. The LEDs, overall they make great replacements for incandescent lights. They last longer, they burn brighter, they're much more efficient.
You don't have to worry about replacing bulbs or worry about brittle filaments with LEDs.This one has a really nice amber polycarbonate lens with a singular white LED. Completely sealed when it comes to the lens and the housing, so it's sonically sealed, features a waterproof housing and lens unit that is submersible. It's a recess mount installation with a built-in mounting flange. It also comes with a foam mounting gasket that creates a weather-tight seal. Your installation area does require a two and three quarter inch diameter hole for this to sit in and then you'll notice that we have three pre-drilled mount holes.
Mounting hardware not included. When it comes to the wiring, it's designed to accept an industry standard two-prong PL-10 plug. That is sold separately and available at etrailer.com. It has this really nice lock clip that creates a secure connection and helps reduce vibration.I'll show you how that functions here in a moment when we hook it up to our power source. This is SAE and Department of Transportation compliant.
It's a PT rated light. When it comes to the overall dimensions of the unit, I took a measurement from edge to edge, got an overall diameter of about three and three-eights to three and seven-16ths inches right in that area. Overall depth from very front to very back, including the clip was one and nine-16ths inches deep. Now, the overall depth once it's installed from the back of the flange right here to the front of the unit, it's only five-16ths of an inch deep, so it's a nice low profile unit. The mount holes are all separated along the center, apart from one another by two and five-eights inches.We're going to go and hook it up to power, that way you can see what it looks like with some power running to it.
We'll open up the clip. This is a PL-10 plug right here. Fits into the prongs here on the backside of the light. Then the clip comes over, snaps into place. That's that locking clip that we talked about. I'll go ahead and run our wires to where they need to go. We'll also be able to turn off our overhead lights so you can see it in a low light setting. You can see here it sends out a nice bright consistent signal. Again, this light contains one LED. When it comes to the power draw at 12.8 volts, it's 0.045 amps, and Optronics puts a lifetime warranty on the LED. That's going to do it for today's look at the Optronics Amber LED Clearance or Side Marker Light.
Average Customer Rating: 5.0 out of 5 stars (2 Customer Reviews)
3-3/8" Diameter round. Waterproof, LED trailer light with reflex reflector serves as a side marker light or a clearance light. Recessed mount with flange. Locking clip minimizes vibration. Accepts 2-prong PL-10 plug. 1 Diode. P2 rated.Quick and easy!
Do you have a question about this Trailer Light?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.