Curt 3-Piece Trailer Hitch Receiver - Multi Fit - Class V - 2"

See what our Experts say about this CURT Trailer Hitch

• Curt Hitch Bolt Holes Will Not Line Up on 1998 Chevy K3500
  So there's one of two things going on here if your Curt 3-Piece Trailer Hitch Receiver # C15511 isn't lining up properly on your 1998 Chevy K3500 pickup. The first possibility, and the most likely, is that the hitch was slightly bent, or "flexed" during shipping. This is unfortunately common but also relatively easily remedied; I have added a link to a help article entitled "My Trailer Hitch Doesn't Fit" for you to check out which has solutions. The other possibility is that you have the...
  view full answer...
• Trailer Hitch and Wiring for a 2012 Lexus RX 350 and What Other Vehicles Will the Hitch Fit
  I have included a link to the hitches that will fit your 2012 Lexus RX 350. The Curt hitch you referenced, # C15511, will not fit. Hitches are custom designed to fit specific vehicles. Multi-fit hitches are no longer being made. If you went with the Curt hitch for your vehicle, which is # C13143, then it will only fit on the following vehicles: 2010 - 2012 Lexus RX 350 2010 - 2015 Lexus RX 450h 2013 - 2015 Lexus RX 350 And, if you were to move the hitch from one compatible vehicle to...
  view full answer...
• Trailer Hitch Needed for a 1997 Ford F-350 Heavy Duty with a Deep Drop Bumper
  The Curt 3-Piece Trailer Hitch Receiver # C15511 that you referenced is a great option for the deep drop bumper on your 1997 Ford F-350 Heavy Duty. The Draw-Tite # 41504 is a little more cost-effective but it also requires the use of the adapter kit # 01685 and it doesn't have as high of a weight rating. We do have a selection of camper tie-downs that you can install on your F-350. If you let me know what the size of your truck bed is and if you have a board or step I can make a recommendation...
  view full answer...
  
• Mounting Hole Dimensions of Curt Hitch # C15511
  The Curt Trailer Hitch Receiver # C15511 measures 33.26" wide, 5.562" between the two mounting holes closer to the rear of the truck, and 11.43" between the center and furthest forward mounting holes.
  view full answer...
  
• Measurement of Curt 3-Piece Trailer Hitch C15511 from End of Mounting Flange to Receiver Tube
  I was able to obtain from Curt a chart showing key dimensions for their 3-Piece Trailer Hitch # C15511 (and other hitch models) that I linked for you. This shows that for hitch # C15511 the overall front-to-back length is just under 24-inches. The height from the top of the mount down to the top of the receiver tube is 8-inches.
  view full answer...
  
• Comparing Regular and Deep Drop Bumper Trailer Hitches for a 1964 Chevy 1/2 Ton Truck
  A standard bumper looks like a regular old bumper that goes straight across at the top and bottom and might have a cut out in the center for a license plate but the cutout does not drop below the bottom of the bumper. A deep drop bumper will have the cut out in the middle but drops below the bottom of the bumper (at the center) so that it angles up from the center to the outer edges of the bumper. I have included a picture that better illustrates this. For models with the standard bumper...
  view full answer...
  
• Availability of Class IV or Class V Hitch Receivers for 1996 Ford F-250/350 With Bucket Truck Frame
  We do have a Class IV trailer hitch receiver from Curt, part # C14082, that is confirmed to fit a 1996 Ford F-250/350 Cab and Chassis style frame. As long as your Ford has 34 inch frame spacing this hitch receiver will fit. It has bolt hole centers that measure 31-1/4 inches that you can use as a reference. Since I am not entirely sure what the details of your specific frame look like, if it looks more like a standard truck then you might be needing one that fits pickups with a standard...
  view full answer...
• Class V Trailer Hitch Fit for 1993 Ford F350
  Because the mounting flange of the Curt # C15511 Class V hitch has 3 tabs on each side, rather than a continuous mounting flange like many other hitches, it'll fit around the rivet shown in your photo. However, be aware that the Curt # C15511 is a fit for cab/chassis models only and won't fit a vehicle that has a standard truck bed on it. Chassis/cab models have a narrower frame which is why this hitch wouldn't work on a pickup model. If you have a pickup model with the 37-1/2 inch frame...
  view full answer...
  
• Class V Trailer Hitch Availability For A 1970 Ford F-250
  I do have some solutions for your 1970 Ford F-250, however, the Curt Trailer Hitch Receiver # C15800 you reference is not a fit for your truck. If your vehicle has the deepdrop style bumper, then I recommend the Curt 3-Piece Trailer Hitch Receiver # C15511. This is also a class V hitch like # C15800, and is rated for 15,000 maximum GTW and a maximum of 1,500 tongue weight. If your truck does not have a deepdrop style bumper, but rather a standard or step bumper, then I recommend the B&W...
  view full answer...
• Is There a Trailer Hitch for a 70s Ford F-250 with Flatbed
  We do offer trailer hitch options for a 1972 Ford F-250 but as far as the flatbed goes, this will be up to you to decide as none of our options are designed for this use. However, the best option would be to go with one that is designed for models with a deep drop tube bumper as this would give you the best chance of compatibility. The Curt 3-Piece Trailer Hitch Receiver part # C15511 is what I recommend and there's a photo below to help you determine compatibility.
  view full answer...
  
• Trailer Hitch for a 1993 Ford F-250 with Luverne 10 Inch Deep Drop Bumper
  We do have some trailer hitch options for a 1993 Ford F-250 with a 10 inch deep drop bumper. Your best option is Curt hitch # C15511 which measures 8 inches from where it mounts to the frame to the top of the receiver opening. Nothing else drops lower than that. This is a Class V hitch. If you just can't get an 8 inch drop to fit then the other option is a weld-on hitch such as # 41990-16. This is a Class V hitch designed for trucks with a service body but it could be used for basically...
  view full answer...
• Curt 3-Piece Hitch Does Not Fit a 2006 Chevrolet Silverado 3500
  The Curt 3-Piece Hitch, part # C15511, is a confirmed fit for only one style of the 2006 Chevrolet Silverado 3500: the Cab and Chassis style. There are two additional styles of the 3500: the Standard Pickup and the Pickup with a 10 Inch Deepdrop Bumper. Unfortunately, if you have either of the Pickups, this hitch will not fit. Whichever you have, you can return the 3-Piece and get the correct hitch for your Silverado. If you have the Standard Pickup, I recommend getting the Curt Class...
  view full answer...
• Side to Side Measurements for B&W Class V Trailer Hitch # BWHDRH25122
  B&W hitch # BWHDRH25122 is designed to fit many trucks including the 1967 Ford F-350 as long as it has (or had) a stock factory bumper. Most of the trucks of that era had a 34 inch frame width which this hitch will fit. But to answer your question the distance between the side plates is 33-3/8 inches and the hole center to hole center distance is 36 inches. I measured them myself. If your frame width is the more uncommon 37-1/2 inch width then I recommend Curt hitch # C15511 which is...
  view full answer...
• Bolt Kit for Attaching Hitch to Chevy C/K Pickup With 8 Bed & Standard Bumper
  To receive replacement hardware your hitch just order etrailer # RHK Trailer Hardware Kit. On the order page you can enter the hitch brand name and model number to get the exact kit that you need. I would not purchase locally as trailer hitch hardware is especially designed for the high stress of towing. If it does not fit you can purchase a new hitch like the Curt # 13028 Class-III with 6000 pounds towing capacity and 600 pounds tongue weight capacity. You could also consider the Curt...
  view full answer...
• How To Find Correct Trailer Hitch Fit for 1993 Chevy K3500
  I have a few different trailer hitch options for a 1993 Chevy K3500. In order to choose the correct one you'll need to first determine if you have a cab and chassis model or a standard pickup. If you have a cab and chassis then you'll need to use the Curt 3-Piece Trailer Hitch Receiver part # C15511 but if not I simply recommend the Curt Trailer Hitch Receiver part # C15317 which is for standard pickup models. Unfortunately, the flanges of these hitch can be reversed and the mounting...
  view full answer...
• Trailer Hitch Receiver and Wiring Harness For a 1972 Chevrolet K-20 Pickup With Step Bumper
  I do see that a deepdrop rear step bumper was offered on your 1972 Chevrolet K-20 pickup. If this is what you have the Curt 3-Piece Trailer Hitch Receiver # C15511 is the receiver I recommend using. Otherwise the Curt Trailer Hitch Receiver # C14082 will fit the standard bumper which came on the K-20 or one of the aftermarket step bumpers that was often used as a replacement. We do have images on our product pages with both these installed so you can see how they will fit with their style...
  view full answer...
• Possible Trailer Hitch Fit for 1958 Chevy Apache
  The frame dimensions you listed for your truck are pretty standard for cab and chassis style trucks since you said 34 inches from outside to outside on the frame. While we don't have anything custom fit for your truck we do have hitches like the # C15511 which is designed to fit that frame dimension and is designed to fit below a deep drop bumper so it would easily clear your bumper as well.
  view full answer...
• Compatibility of a Hitch for a 1972 Chevrolet K Series Truck
  The Curt # C15511 hitch is the confirmed fit for a 1972 Chevrolet K Series truck if you have the 8 foot bed and the deep drop rear bumper. The measurement from the top of the tube to the mounting flange is 8-1/32 inches. The extended length was to make sure the hitch would clear the bumper. If you have the standard bumper, then the Curt Hitch # C14082 is the confirmed fit. If # C15511 can be installed on the standard bumper model, then there will be a large gap between the bumper and...
  view full answer...
  
• Hitch Recommendation for 1974 Chevy C10 Stepside Pickup
  If your truck has the standard bumper, I'd recommend the Draw-Tite Class 5 hitch, part # 41947. If you have the deep drop bumper, use the Curt # C15511. I've linked you to an FAQ article that explains the difference between the standard and deep drop bumper. If you need to install a 4-pole trailer connector, use # 118311. You might also need a ball mount like # 2753, a 1-7/8 inch trailer ball like #19260 or a 2-inch trailer ball like part # 63845.
  view full answer...
• Recommended 15K Hitch For 1997 Ford F-250 With 34 Frame
  The only option that provides 15,000 gross towing weight capacity is the Curt Class V Receiver Hitch - 1997 Ford F-250 and F-350 Heavy Duty part # C15511 which is designed for the 34" frame but is also a universal fit hitch so there is drilling into the frame required. All of the hitches available for this truck do require some drilling so this is your best option.
  view full answer...
• Possible Hitch fit for 1998 Chevy K3500 Cab and Chassis with Dump Bed
  I really wish we could guarantee a hitch fit but since you have the dump bed and the tank there isn't a way we can verify any of our fits. The Curt # C15511 does fit your 1998 Chevy Cab and Chassis frame and has an 8 inch drop from the hitch tube to the frame attachment point and 6 inches down to crossbeam which would be our best possible option.
  view full answer...
  
• Recommended Trailer Hitch Receiver for 1964 Chevy C/K 20 4x4 and 2001 Ford F-350 Front Hitch
  Although the Draw-Tite # 40050 is only for 1964 Chevy C/K 8 foot bed 2WD as you stated, there are other options available for your 4x4 truck. I recommend the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" Item # 13028 which is a fit for your truck if you have a standard bumper. If you have a deep drop bumper, then I recommend the # C15511. All of these hitch receivers are compatible with the Gen-Y Iron Grip Anti-Rattle Hitch Pin for 2" Hitch Receivers - 5/8" Diameter, Item...
  view full answer...
• Determining Correct Trailer Hitch Receiver For 2000 Chevy K3500 DRW With Dump Bed
  I would be happy to help. The Curt Trailer Hitch Receiver # C15511 measures 33.26" wide, 5.562" between the two mounting holes closer to the rear of the truck, and 11.43" between the center and furthest forward mounting holes. The Curt # C15317 you were looking at measures 34-1/2" wide, 9-5/8" between the furthest forward mounting hole and the center mounting hole, and 4-7/8" between the center mounting hole and the furthest back mounting hole as you can see in the included diagram. Theses...
  view full answer...
  
• Trailer Hitch and Wiring for a 1977 Chevy C10 Pick-up with 6 Foot Step Side Bed
  We do have trailer hitches that will fit your 1977 Chevy C10 short bed but # C13099 is only for long bed models. For your truck you can use Curt trailer hitch # 13028 unless it has the 10 inch deep drop bumper. If it does have the deep drop bumper you can use # C15511. If you plan on doing some towing I recommend etrailer ball mount kit # EBMK4. It comes with a ball mount with a 2-3/4 inch rise or 4 inch drop, interchangeable ball set, hitch pin with clip, and a storage bag. If the ball...
  view full answer...

Do you have a question about this Trailer Hitch?