Brophy Slide In Camper Tie-Downs - No Drill Bed Mount - Qty 4
(218 reviews)
Price: $203.79
In Stock
Brophy Slide In Camper Tie-Downs - No Drill Bed Mount - Qty 4
Item # HSSF
Retail:$220.09
Our Price: $203.79
You Save: $16.30
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (218)
- Q & A (0)
- Photos
- Used (1)
Brophy Camper Tie-Downs - HSSF
- Front and Rear Tie-Downs
- Brophy
- Bed-Mounted
- Powder Coated Steel
Steel brackets clamp onto the side rails of your non-dually, full-size pickup with no drilling required. Creates a dependable anchor point for securing your lightweight camper to the bed. Simple to install and to remove.
Features:
- Creates attachment points for securing your camper to your truck bed
- Wide clamps provide superior holding strength
- Turnbuckles (sold separately) required to attach camper to tie-downs
- Protects your truck's paint with neoprene pads attached to the brackets
- Resists corrosion and rust with black powder coated steel
- Clamps securely onto your bed rails - no drilling required
- Includes 4 camper tie-downs with clamp plates, 12 neoprene pads, and installation hardware
- Made in the USA
Specs:
- Application: for exact fits, enter in your vehicle's year/make/model above
- Minimum 2" needed between sidewall and lip of bed rail
- Not compatible with drop-in bed liners, aftermarket bed rails, double-walled beds, or side-step beds
- Dimensions: see diagrams below
- 1-Year limited warranty
No-Drill Installation
These clamp-on tie-downs install quickly and easily, with no drilling or modification to your truck required. Because they're mounted in the bed instead of on the frame or body of your truck, you don't need any kind of fancy mechanical background to get this job done. You just need to slide the hold downs over the rails of your truck and clamp them down with the included T-bars and hex bolts.
The fact that they simply clamp on means that you can remove these tie-downs when you're not hauling your camper, leaving no trace. Use the provided neoprene pads on the T-bolts and tie-downs where they make contact with your truck to make sure no scratches or dents will be left behind either.
It's important that the tie-downs on your truck line up with the anchors on your camper at the correct angle to ensure a secure hold. Ideally the tie-downs should be on the outside of your camper's anchor points, but they can be on the inside as well, just as long as they're not lined up with each other.
Securing your Camper
To secure your camper to your truck, you'll also need a tie-down hardware package consisting of turnbuckles, S-hooks, and chains (TDHP - sold separately). This hardware attaches the anchors on your camper to the tie-downs on your truck to keep your camper safely mounted. Once you tighten the turnbuckles to the correct level of tension (not too tight!), you'll be good to hit the road.
HSSF CR Brophy Truck Camper Tie Downs for Slide In Truck Camper - Camper Hold Down - No Drill Tie Down - 4 Pack
Installation Details
Customer Satisfaction Score:
90% were satisfied with this product
10% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- etrailer mistake
Customer Reviews
Brophy Slide In Camper Tie-Downs - No Drill Bed Mount - Qty 4 - HSSF
Average Customer Rating: 4.6 out of 5 stars (218 Customer Reviews)
Steel brackets clamp onto the side rails of your non-dually, full-size pickup with no drilling required. Creates a dependable anchor point for securing your lightweight camper to the bed. Simple to install and to remove.by: TheAvionNomad01/18/2024
I used these to mount a vintage 1970 Avion C-11 to a 1993 D250. They worked great and were much stronger than I expected - and it was a huge cost savings (and a much more attractive look) than some of the frame mounted options of more than $1000. There were some oddities that I noticed. It was impossible to mount them exactly the way the instructions suggested because of where on the wings near the cab,. The brackets also could not stay on with the camper unloaded because they would hit the jack mounts, meaning they had to me bolted in after the camper was in the truck but before lowering the jacks, making the access to the bolts a frustrating 'feel for it' experience.I'f suggest the manufacturer secure the bolt so that you don't need to hold both sides when tightening/loosening, and also refine it to need less turns to do so. It took me 2 hours to mount the first time, and not much less when removing them with the limited access. The pads also came off in the first use.
I gave it a 5 star because I realize there are limited options for older campers and anything universal is going to have issues with some thing - so that's just my input and experience. Overall pretty reasonable for the price and functionality.
by: Pat03/20/2023
The product was shipped extremely quickly, it arrived 3 days after I ordered them. As far as the product goes I was extremely pleased that they were as easy to install as the product video showed them to be. I had been looking for
a tie down system that would work for my 2018 Ford since I purchased my camper in 2020 and after much research I found these at etrailer. One word of advice is that if your camper has a shower or other design that allows the camper to extend across the bed behind the wheel wells, either move the rear tie downs forward or shorten the leveling stud before you attempt to load your camper. On mine it turned out that once the tie downs were placed and attached I had to cut off about 3 inches of the threads.
Other than that it was an easy install although the bolts that attach the tie downs to the under lip clamp are a challenge to install but take your time and they will go on. I will post an update once I have been on the road for a few trip and see how they are working.
Thank you etrailer for your super fast shipping and online product videos.
by: Ed B.05/21/2019
Purchased the Brophy camper tie down set of four for the Palomino truck camper I just purchased. These are my second set as the first set were sold with my Hallmark camper. Easy to install and hold the camper in the truck with no worries.
by: James 05/20/2024
Ordered these for new camper. Very easy to install and does the job without the high cost of frame mount.
by: Jeff Smith10/22/2023
These tie downs work great. It holds my 3k lb Cabover camper in place without issues. And I live in my camper, so not losing my home is very important to me!!
by: Shelly12/13/2023
The products arrived on the time scale as stated. The packaging did not hold up and the box with the metal tie downs was broken open. There was too much weight for the box and it just split open. Not sure if anything is missing. Packaging of items that are heavy should be more secure and sturdy.
Jenny N.
12/14/2023
Oh no! I will have our Customer Service team reach out to you. If anything is missing we can take care of it.
by: Allen.08/22/2022
These wont work for my truck and camper. The box on a 2018 gmc 2500 short bed does not lend well to placement of these in order to get the correct geometry i needed for the tie-down points on my Palomino maverick 6601. I had high hopews of not having to buy the frame mounts, but i will have to.
Mike L.
8/31/2022
The HSSF tie downs have specific fit parameters as mentioned in the product specifications above: External bed rail width cannot exceed 5-12 Requires at least 2 of space beneath lip of bed rail Not compatible with -in bed liners, bed rails, double-walled beds, or side-step beds
Allen.
8/23/2023
In response to the etrailer comment response, they fit on the bed fine, with plenty of clearance and would work for a smaller camper. they just did not fit in the right spots for my truckcamper combo.
by: Ron W07/02/2016
As far as I'm concerned these are junk. Wasted my money. Do not mount in proper location on a 2011 Chevy Silverado 6.5' Bed. Because of the design of the bed rail the mounts cannot be installed in the proper locations for securing camper. The photos show the maximum forward and back that these can be mounted. Not at all made for the 6.5 foot bed 2007 or later Siverado. The Black Powder Coated Steel isn't that great either. Paint missing, dinged up from storage and shipping probably.
by: . George01/03/2024
The tie downs are great no problems.Very easy to install.I keep them on my truck all year long Thank you
by: Terry08/08/2023
Order arrived quickly, priced ok. Box was broken open by shipper NS the 4 T-bolsts bolts ere missing. Etrailer shipped ou the missing parts a few days later, but in the meantime I fashioned t-bolts I could use for my trip. Many customer comments on this camper Brophy tie-down match my experience. Etrailer follow up was great, but surely must be aware that their packing is sub-standard. Perhaps zip-tying the T-bolts to larger pieces would eliminate the loss even in case of breakage. Functionally the tie-dows were easy to install and seem quite adequate for off-road use of my in-bed camper. Will continue to use etrailer because of their excellent customer service.
by: captkirk02/15/2021
These tie-downs worked awesome for our pop up camper on our 1998 F150. Super snug, haven't loosened up or moved on the truck, camper hasn't budged either. I was leary at first not having the camper tied to the frame but now I have total faith in these tie downs.
by: Mike S05/23/2020
These Brophy tie downs have worked great over the past year. I leave the camper on the truck and it is my daily driver as well as RV. The camper weighs in at 1500 dry and about 2000 loaded. I do not do any radical 4x4 but I have taken some backwoods off road logging trails.
by: Bing09/23/2019
I received this tie downs on July, and first used it yesterday.
My Camper ‘s dry weight is about 1600 lb, and the products are good for my truck camper.
The problem was the position where tie downs were fitted on my truck. I tried several times to fitted tie downs to my truck.
by: Brent 08/08/2019
I bought these for our brand new 2019 GMC Sierra 1/2 ton because no custom options were available. I was happy that they were easy to install, and look great. I’ve used them in the past and have been happy with how they hold campers. Sure I’d rather have custom mounts from the frame, but for the price and because these are my only option that’s what I got. These will work just fine, and I like that I can swap these out on trucks.
The one thing I wish was different was that the threaded T handle portion would have a longer option. I had to fancy up a 2”x6” to run inside the side of my p/u bed so they would touch something.
As always another great shopping experience with etrailer. They haven’t let me down yet. Especially Lori, what a great customer service rep.
by: Matt04/14/2015
These camper hold-downs appear to be manufactured from good steel stock and should do the job nicely. I did have one piece that was slightly damaged but was not caught when packaged (the damage was not due to shipping). I was able to take a hammer to the bent steel and straighten it sufficiently to use the part. It was a little disappointing however, and should have been caught prior to shipping.
Overall I am pleased with the quality and price
by: Patrick04/02/2020
These things are solid although i put duck tape on the T pads....installed 2014 Chevy Silverado 6.5 ft bed for 1200lb Starcraft.
Patrick
4/6/2021
Still have not moved! Great design and cost savings.
by: Regan06/25/2019
Using on 2013 Ford F150 for a smaller cabover. Great quality product, shipped fast, works great. Had to turn bolts around to clear inside of bed. Held camper solidly over rough trails!
by: Bryce05/10/2022
Fits well on a First Gen Tundra. I was extremely unsure about fitment for my truck but they work great! Install only takes 5-10 minutes. I would definitely recommend. Steel is quite thick and seems very strong.
by: John05/25/2020
Easy to install and have done what’s expected. Keep the camper in place!!
by: JAMES K09/24/2012
ORDER ON TUESDAY RECIEVED ON FRIDAY NOON SAME WEEK ONLY PROBLEM WAS 4 7/ 16 NUT WERE 4 1/2 NUT HAD TO BUY 4 NUTS OTHER THEN THAT I WOULD BUY OFF ETRAILER AGAIN VERY GOOD SERVICE
by: Chuck11/13/2012
Found easy to install, I placed lock washers on the 8 3/8" bolts. Sold at Menards for 89 cents (pkg of 8) not in kit. Placement was a little restrictive with dealer installed bed liner. Takes 30 minutes to install all 4. Great buy.
by: Neil08/04/2021
Arrived on a rainy day with the box falling apart. Too much heavy steel to be loosely packed. Fortunately, the hardware bag was still there. Some bare metal showing. I had some emails with MacKenzie B. and they were responsive and without asking they offered me a 5% refund for the damage. After my first trip, they performed well on some very bumpy roads. Held strong and didn't move. I did have to re-adjust the lower standoffs after the first week. Taking them on/off is frustrating because the 2 nuts are in the small gap behind the clamp against the inner bed wall. Too tight for all but an open end wrench. 1/6 turn times too many fumbling tries, arg! Also, I was nervous not having a locking feature (lock washer, locknut, etc). I bought 8 locknuts (pinch type) and welded them to the inner plate. Then bought 8 round head hex bolts (grade 8). So now I can install easily with an Allen socket. See pictures. Recommend eTrailer consider this modification.
Neil
8/5/2022
After my mount bolt mod, Ive used these multiple times and they are working great! Very stout and no visible marks on my F250 bed.
by: Jason S.06/05/2019
These tie downs were a great budget solution in leu of a permanent installation of my camper shell and/or frame mounted tie downs. Aside from needing to plan their placement (they can hang in front of the gas cap if you don't plan it right the first time around... no, I didn't accidentally block my gas cap... maybe I did) and take into consideration they also need a little bit of internal clearance as well, they work just fine. I haven't noticed any cargo shifting nor warping of the truck bed around where they are installed. My camper shell is under 1K lbs and it holds just fine.
Jason S.
6/8/2020
A year later & they still hold strong.
by: Dayton12/15/2023
Awesome customer service my new fav pl ace
by: dave07/08/2016
Its a good product for a light camper. I personally would not use it on anything heavier than 1000lbs. But then iam not an engineer. I sold mine and my camper and bought frame mounted tie downs
Dave
7/11/2017
Did not work for me. Tried to send them back but shipping would cost a bundle so i would get less than half of what i paid. Sold them same day on-line. Not good for a larger camper.
Rachael H.
7/12/2017
25
218
Show More Reviews
See what our Experts say about this Brophy Camper Tie-Downs
- Camper Tie Down Availability for a 2013 Chevy Silverado that Attach to Bed RailsYes, the Camper tie downs part # HSSF will work on your 2013 Chevy Silverado but there is another option for you to consider. I contacted our representative at Brophy about the differences between the Tie Down Anchor, part # TDSF, and the Camper Tie Down, part # HSSF. Part # TDSF can be used on campers that have a total length of up to 8 feet in length. Part # HSSF can be used on any size campers. Part # TDSF mounts into the stake pocket, where as part # HSSF mounts over the sidewall...
view full answer... - If Brophy Camper Tie Downs Bend Can they be Bent BackIf the bend wasn't enough to affect the integrity of the tie downs then yes you could bend them back. So basically bend them back and as long as you don't see any metal creasing, paint flaking, or any other obvious signs of stress you'd be fine. If they are stressed to the point they need replacing these have a 1 year warranty.
view full answer... - Will Camper Hold Downs HSSF Fit a 2010 Dodge RamMy contact at C.R. Brophy let me know that though they have not been able to test the # HSSF camper hold downs on the 2009 or 2010 Dodge Ram models, they should still be a fit for your truck. You will want to check, however, that your vehicle manual does not state that you would be unable to use sidewall type camper hold downs.
view full answer... - Will the Camper Hold Downs, # HSSF, Fit on a 2005 GMC SierraThe Camper Hold Downs, # HSSF, will work on your 2005 GMC pickup. These hold downs wrap around the truck bed rails and are mounted inside the bed. They do not fit in the stake pockets. These hold downs will work for any camper that is a correct fit for your vehicle. To install, first place the protective tape under the rest plates and on the T-Bars. Next, thread the T-Bar into the nut at bottom of each Holdown. Then place the front two Holdowns as forward as possible on rail of your truck...
view full answer... - Hardware Needed to Mount a Camper in the Bed of a 2002 Ford F-150To mount your camper in the bed of your 2002 Ford F-150, you can use the Brophy Camper Tie Downs, # TDSF, as long as your camper is not longer than 8 ft. These tie downs will install in the stake pockets on the top of your truck bed walls. If your camper is longer than 8 ft, then I recommend using the Brophy Camper Hold Downs, # HSSF. These hold downs will not install in your stake pockets, but clamp around the inside lip of the bed rail (see photo). The underside of the bed rail must...
view full answer...
- In-Bed Camper Tie-Down Options for a 1992 Chevy K1500 Short BedThe best and most secure tie downs for a truck bed camper are going to be custom fit brackets. There are several options for a 1992 Chevy K1500 depending on its configuration. If you have running boards that extend past the truck cab and a factory trailer hitch you can use front tie downs # TLC4201 but there are no rear options for this configuration. If your truck has running boards that extend past cab and with a non-Torklift aftermarket hitch you can use front tie downs # TLC4201 and...
view full answer... - Which Brophy Camper Tie Downs Fit 2001 Toyota TundraFor tie-downs that will work in your 2001 Toyota Tundra you will want the Brophy Clamp On Camper Tie-Downs # HSSF. Brophy has told us in the past that the # HSWB was intended for domestic trucks. These tie-downs are compatible with the turnbuckles # TDHP that you'd need to complete your camper tie down setup for your truck. This provides the connection from the tie down to the camper. I attached a review video for more info as well.
view full answer...
- Recommended Camper Tie-Downs and TorkLift Trailer Hitch for 2018 Ford F-350I do have an option for you, however there is not a set of TorkLift Custom Frame-Mounted Camper Tie-Downs available that will work with the running boards on your 2018 F-350 that run beneath the bed. I instead recommend taking a look at the Brophy Clamp On Camper Tie-Downs # HSSF. These are universal tie-downs that will clamp onto the truck's bed side rails to provide attachment points for securing your camper. They feature a strong steel construction with a black powder coat finish to...
view full answer... - Camper Tie Down Recommendation for a 2000 Chevy 1/2 Ton SilveradoThere are several camper tie downs that you could use depending on how you want them to mount. First, the Camper Tie Downs, # TDSF, that you have referenced will fit your truck and fit in the truck stake pockets. If you do not want something in the stake pockets, then I recommend going with Camper Hold Down, # HSSF, which wrap around the bed side. For either kit, use Camper Tie Down Hardware Package, # TDHP.
view full answer... - How to Tell If Brophy Tie-Down Kit Will Fit 2012 Ram 1500 PickupI'm pretty sure that the Brophy Clamp On Camper Tie-Downs # HSSF will fit your 2012 Ram 1500 just fine since we have had others with similar model years get them to fit, but since these are universal tie-downs I don't have a way to confirm this on my end. With that being said, I'm attaching a photo showing the dimensions of these tie-downs for you to compare with your side rails to make sure that they fit properly. If they do then all you need to finish your setup is the Brophy Basic...
view full answer...
- Is There a Set of Torklift Tie Downs that Fit 2004 Toyota TacomaWe have a set of Torklift camper tie downs that fit the 2004 Toyota Tacoma with the part numbers # TLT2306 and # TLR3500.
view full answer... - Camper Tie Down Recommendation for 2012 Nissan TitanBrophy tie downs, # HSSF, will work well for you. This setup is rated for use with any camper that fits the bed dimensions of your truck so it would work well with yours. We do not carry the donuts you mentioned that usually go around the center window of the rear window.
view full answer... - Will the Brophy Camper Hold Downs Fit a 2012 Chevy Silverado 1500 with 6-1/2 Foot BedIf it is not a dually and does not have a step side or double wall bed, then the Camper Hold Downs, # HSSF, will fit your 2012 Chevy Silverado. These hold downs wrap around the bed rather than fit inside the stake pockets and will work for any camper that is a correct fit for your vehicle. You can also use camper tie down hardware kit, # TDHP, with the hold downs. To install, first place the protective tape under the rest plates and on the T-Bars. Next, thread the T-Bar into the nut at...
view full answer... - Recommend Camper Hold Downs For 2500 lb CamperBoth the Erickson Tie Down Anchors, part # EM01003 and the Putco Push-Up Tie-Downs, part # P99901, are not designed to be used to hold down campers. The capacity of the Erickson Tie Down Anchors, part # EM01003, is 1,000 lbs. For a camper tie downs, I would recommend using the Brophy Camper Tie Down, part # HSSF. These camper tie downs are made to be used with the bigger size campers and do not have a capacity. If you have a slide-in bedliner, you will have to trim it or remove it to use...
view full answer... - Camper Tie Down Recommendation for a 2003 Toyota TundraFor your 2003 Toyota Tundra you would want the Tie-Downs part # TDSF. We had a customer use these on his 2005 Tundra (same generation as yours) and let us know that they worked very well for him. The # HSSF that you referenced is a universal kit that could work for your truck, but we don't have fit information for this kit so your best option would be the # TDSF since we know it would work for you. You also will want the Camper Tie Down Hardware Package, # TDHP.
view full answer... - Camper Tie-Downs for 2007 GMC Sierra 2500 New Style with 6-1/2-ft BedThe correct choice of camper tie-downs for your 2007 GMC Sierra 2500 New Style with 6-1/2-ft bed will depend on whether it is equipped with running boards and on what type of hitch is installed: factory, aftermarket or Torklift. The link provided will take you to our main page for tie downs for your truck. The drop-down 'Select Vehicle Style' menu at the top of the page will let you select your particular truck's configuration to see compatible tie down kits. For example, if your truck...
view full answer... - Camper Shell Hold Down Recommendation for a 2013 RamIn order to determine if the camper shell from a 1997 Dodge Ram could fit on a 2013 Ram you will need to measure the dimensions of both truck beds. If the dimensions are the same then the camper should fit on either truck bed. Without knowing more information it's hard for me to be any more helpful. If you need camper hold downs the part # HSSF and the hardware kit part # TDHP.
view full answer... - Spring Loaded or Rigid Turnbuckles for CR Brophy # HSSF Truck Bed Camper Tie-DownBrophy recommends using their rigid tie down hardware kit, part # TDHP, as their tie downs provide a small amount of flex.
view full answer... - Camper Hold Down Black Powder Coated Finish, # HSSF Recommendation for a 1992 Chevy TruckFor your 1992 Chevy Truck you would want Camper Hold Down Black Powder Coated # HSSF. The hold downs wrap around the truck bed rails and mount inside the bed. They do not fit in the stake pockets. These hold downs will work for any camper that is a correct fit for your vehicle. The Camper Tie Down # TDSF that you referenced will not work on your vehicle as it is only designed for Chevy trucks that were made before 1988 Chevy trucks.
view full answer... - Brophy Camper Tie Downs that Can be Used with 2021 Ford F-150 with Aluminum Truck BedYes, we've checked with Brophy in the past and their camper tie downs part # HSSF are perfectly compatible with the aluminum bed of the 2021 Ford F-150. Turnbuckle kit you'd also want the part # TDHP.
view full answer... - Camper Tie-Down Fit For 2007 Toyota TundraThe Brophy Camper Hold Down # HSSF is a more universal fit style camper tie-down. We unfortunately do not have test fit information on them, and have not had the chance to install them ourselves on a 2007 or same generation Toyota Tundra. We did have a customer purchase the # HSSF for his 2000 Tundra, and he did not have any issues with them fitting over the sidewall of his truck bed. The # HSSF comes with 4 camper tie-downs. We do offer custom fit camper tie-downs for your 2007 Toyota...
view full answer... - Camper Tie Down Recommendation for 2013 RamYes, the stake pocket camper tie downs, # TDSF, will work on the 2013 Dodge Ram, as long as the overall length of the camper you are using them with is 8 feet long or less, this measurement includes the overhang over the cab of the truck. You will need to drill one 11/32 inch hole and two 7/32 inch holes for this installation, and there are spacer tabs on the tie downs that may need to be pried off for a proper fit in your stake pockets. If your truck campers overall length is longer...
view full answer... - Can I Use the Brophy Clamp On Camper Tie Downs on 2019 Ram 2500 With Double Walled BedAs long as the double wall still allows for the clamp on the underside of your bed rail, the Brophy Tie-Downs # HSSF will work on your 2019 Ram 2500. The brace on the bottom is adjustable so it will account for the additional wall on the inside of the bed. If you don't have the lip under the rail then you may want to instead consider the Brophy Stake Pocket Mounted Camper Tie Downs - Bed Mount - Black Powder Coated Steel - Qty 4 # TDSF since they won't utilize that lip or the inside of...
view full answer...
- Brophy Truck Bed Camper Tie Downs for 2009 Ford F-350As long as the underside of the bed rail lip is at least two inches wide (see diagram I've provided for you), the CR Brophy # HSSF camper tie downs are what I'd recommend. You'll also need the tie-down hardware package, part # TDHP which includes the S hooks and turnbuckles. If you click the link, you can see a demonstration video showing how the tie downs work.
view full answer...
Do you have a question about this Camper Tie-Down?
Used Items Available
Condition: Surface Scratches
Notes: Parts are scratched up, seems to be some signs of instalation, otherwise fine.
Info for this part was:
Expert Research:
Mike L
Expert Research:
Sarah L
Expert Research:
Robert G
Expert Research:
Patrick B
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Reno H
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Brandon M
Expert Research:
Adam R
Expert Research:
Jeffrey L
Expert Research:
Sarah H
Video Edited:
Zack K
Video by:
Patrick B
Installed by:
Matthew K
Installed by:
Cole B
Updated by:
Rachael H
Updated by:
Amanda M
Updated by:
Manda E
Updated by:
Amanda K
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
Ed B.
5/22/2020
No problems. Would buy again. Very easy to take on and off the truck.