Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
(220 reviews)
Price: $77.32
In Stock
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
Item # D210
Retail:$109.08
Our Price: $77.32
You Save: 29%
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (220)
- Q & A (0)
- Photos
CURT Trailer Hitch Ball Mount - D210
- Fits 2 Inch Hitch
- Fixed Ball Mount
- Drop - 2 Inch
- Rise - 0 Inch
- No Ball
- 7500 lbs GTW
- Class III
- CURT
- Built-In Dual Hitch
- Steel Shank - Gloss Black
- 1 Inch Ball Hole Diameter
Carry accessories such as your bike rack or cargo carrier while also towing with this multipurpose ball mount. Receiver intended for accessories only. Do not exceed 750 lbs of total tongue weight while towing.
Features:
- Ball mount lets you hook up your trailer to your tow vehicle
- Shank slides into your vehicle's hitch receiver
- Ball platform provides mounting point for hitch ball
- 2" Square receiver allows you to carry hitch accessories while you tow
- Perfect for a bike rack or cargo carrier
- Sturdy steel is black powder coated for corrosion resistance
- Hitch pin and clip included - hitch lock sold separately
- Assembled in the USA
Specs:
- Application: 2" x 2" trailer hitch receivers
- Ball mount
- Gross towing weight: 7,500 lbs
- Tongue weight: 750 lbs
- Ball hole diameter: 1"
- Drop: 2-1/4" from top of inside of vehicle's hitch opening to top of ball platform
- Length: 12-1/2" from center of hitch pin hole to center of ball hole
- Accessory receiver size: 2" x 2"
- Tongue weight: 750 lbs
- 7-1/2" Extension from center of hitch pin hole to center of accessory receiver's hitch pin hole
- 3-9/16" From top of shank to bottom of accessory receiver
- Pin hole diameters: 5/8"
- Limited lifetime warranty
Notes:
- The receiver portion of this unit is designed for hitch-mounted accessories only.
- Do not use with an additional ball mount to tow a trailer.
- When mounting an accessory in this receiver, your hitch's tongue weight capacity will be reduced by 50 percent.
- When using both the ball mount and the receiver the tongue weight capacity is not affected.
45810 Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs
Customer Satisfaction Score:
92% were satisfied with this product
8% of customers were not satisfied
- Wrong item was ordered
- Product did not meet expectations
- etrailer mistake
Customer Reviews
Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers - 7,500 lbs - D210
Average Customer Rating: 4.7 out of 5 stars (220 Customer Reviews)
Carry accessories such as your bike rack or cargo carrier while also towing with this multipurpose ball mount. Receiver intended for accessories only. Do not exceed 750 lbs of total tongue weight while towing.by: John01/26/2023
I am using the hitch for a car dolly and a bike rack. The fit is a little loose for the bike rackmI'll see it really works when get on the road.
by: Carol12/01/2023
Quality is excellent. However, it did not work so I am not sure what to do with it. I thought I could use the top hitch for a Bike rack and pull a utility trailer with other toys. The trailer is too close to make a turn so good try but not able to use it. Thank you for asking. I did not open the box for a while because I was having the trailer worked on so assumed I waited too long to return.
by: Ray12/21/2020
We sold our small motor home and purchased a small travel trailer. This hitch provided a perfect solution to how to use our bike rack while towing the trailer. It even allows room for the pickup tailgate to be lowered without removing the bikes from the rack.
The hitch is very hefty with a high weight limit - plenty for the GVW of the trailer (7,000#) plus 125# of rack and bikes.
Ray H.
12/22/2021
Great solution for taking our bikes camping while towing our trailer
by: Debbie04/21/2021
This has been an amazing multipurpose ball mount. We purchased this to use with our Hollywood Bike Rack and also to connect onto our boat. We weren't sure if this would work, but it was awesome. It is very well built and We had to make some minor adjustments to the position of our boat on the trailer so the turning radius of the bike rack that was attached would clear the truck. This is very well made and solid.
Debbie
4/22/2022
Excellent. This has been an awesome product.
by: bruce11/02/2021
Once the bike rack and the ball are installed there is only 3" of space for the trailer coupler to attach to the ball. Mine open hitch height is 4 ½”, most others are similar. I cannot think of any trailer/rack combination that this could even be used for. The only way it could be used would be to hitch up the trailer then attach the rack then load the rack over the trailer. Not a good or safe proposition. The only way to detach the trailer would be to unload the rack and then remove it from the mount.
Jenny N.
11/3/2021
Thank you for your feedback. The solution that I have would be to switch to a hitch mounted tow bar that slides into the RV receiver - making sure that the brand matches base plate - and then you could use a hitch adapter like part # RM-077-6. You would also want to make sure that the tow bar was as level as possible.
by: Stephen E06/16/2020
Installed on my 2006 GMC Envoy. Mounted a Bump Step with a self installed camera. Now have full access for adding my trailer as needed.
Stephen E.
6/17/2021
Absolutely still in love with this product!
by: peanuts06/26/2014
I have been looking for a light up trailer hitch for a long time. So when I saw this one from etrailer I was very happy. I ordered it and it came in few days.
I also purchased the Curt Multipurpose Ball Mount with 2" Receiver so I could mount the light and still be able to tow with out switching them out. Both Product's are perfect for my needs. Your company is the best and I would definitely recommend Etrailer to others.
Thanks for the great service!
by: Chris H03/08/2017
We use this on a luggage carrier on a Mercury Grand Marquis. My son hauls lawn mowers on the rack and it works great. Very well made
by: Ron10/13/2018
Delivery was fast. Arrived in well packed box. Installed product with no issues at all. Works great and as advertised. Will be towing a travel trailer and needed a connection for a bike rack. When all installed, have plenty of room for placing bikes on bike rack. Really like this product!
by: VickieB6803/15/2017
Raised receiver portion was exactly what I needed to attach my cargo carrier, as my Grand Caravan Receiver was too low to the ground.
by: Mike11/12/2017
Extremely heavy duty. I will be towing a small aluminum boat behind our camper, and will build a 2 X 2 tube assembly to carry the spare tire on. I needed something to help carry my trailer spare as the hitch on the camper is mounted in such a way that I couldn't hang my spare tire on the bumper. This assures a way to carry the spare as well as tow my fishing boat!
Mike
Mike H.
11/15/2018
A year later, still functioning as designed. I found my hitch pin hole to be slightly off but was able to make it fit. Still hauling the boat and carrier.
by: Chad07/26/2012
This multi hitch receiver fits our needs great. We need to use it for hooking up our pop-camper and for our bike rack. With this receiver, we can now take our bikes with us and not have to mount the bikes on the camper.
The delivery time was fast. We ordered this on a Sunday evening and we received it on Wednesday.
The only thing that we would change is that if the top receiver was about an half inch or more higher, then we would have more than enough clearance for our camper locking part, but there is enough clearance to make this system work.
Stefan
6/14/2013
how many bikes does your bike rack hold? and, have you noticed any problems with turning sharp corners and your bikes coming into contact with your tent trailer?
by: Andrew 09/06/2023
Great product. Highly recommend.
by: Robert G.05/15/2012
WOW! This piece of gear is built so solid that it is never a worry hooked up to my motorhome, towing a two wheel dolly with a Jetta Diesel Sportwagon and a 4 place bike rack in the upper reciever!
The turn around time between order and delivery was very quick and I was kept aprised of shipping during the entire time.
Thanks!
Anonymous
9/9/2015
It appears that other comments say that in order to remove the car dolly from the ball, you have to remove the bike carrier. This seems to make the whole thing not very good. You do not mention this problem. It appears from the comments, the problem relates to the lack of space between the two receivers
by: RHK02/06/2017
This is a heavy duty receiver it will work great for towing a trailer and having the ability to add a bike rack or cargo carrier. Etrailers coustomer service is outstanding always easy to order and fast shipping with great prices.
Rhk
2/6/2018
The receiver is still working great no problems or issues are all.
by: Chris10/05/2021
Disappointing. Although the manufacturing quality is consistent with Curt's normally high standards, the design leaves everything to be desired. There is not enough clearance above the trailer tongue coupler latch to mount a bike rack. Even if you somehow manage to overcome this, most bike racks won't clear a telescoping jack stand. I should have sent this one back!
Sierra K.
10/14/2021
A very valid issue. It can be done, but you will have to measure carefully to see if this piece will work with your set up. The measurement is 3 and 9 sixteenths of an inch from the top of shank to bottom of the accessory receiver. I recommend getting a bike rack with a rise as this will be the best option for you.
by: Kelly B06/17/2017
Great product, but did not fit on my 2014 Traverse. The top receiver would rub on my fiberglass bumper of the Traverse and therefore only half the pin hole would line up with the receiver. Plus my 4 bike rack would not fit between car and pop up camper then.
Kelly B.
6/19/2018
Works wonderfully. Use it a lot and couldn’t be happier .
by: Doug T.07/20/2015
This was just what I was looking for to raise my cargo carrier above the level of my car exhaust and will work for my bike rack as well (not at the same time). It will also allow more room to open the rear lift gate. Product appears to be of high quality but I haven't had a chance to use it yet. Shipping was fast.
Doug T.
7/19/2016
Ive had the receiver about a year now and have used it several times. Its well built and and works for what I purchased it for.
by: Stan06/15/2018
I have never seen a hitch like this one, that I found on etrailer.com. I saw this hitch, and knew it would be perfect for my side by side, and it is. I can hook up to a small trailer, and then unhook, and slide in a feeder in the top receiver, and feed the roads of our hunting lease. This thing is perfect!!
Stan O.
6/15/2019
Perfect!
by: Billy 10/19/2023
Great customer service and excellent pr oduct.
by: John H.02/02/2017
Very good service and shipping was on time. Good value for the quality of the ball mount receiver. I tow a car dolly behind my motor home and needed a place to mount my spare tire. Like the fact it's made in the US. very well built.
John H.
2/2/2018
I often dolly tow our vehicle behind our motorhome, but I cannot attach or detach the dolly from the ball mount without removing the bike rack mount receiver first, due to the height and the ball mount . I cannot release the tongue trailer coupler lever. Too tight of clearance. I wish the ball drop was at least 6 inches. This would allow for the dolly tongue trailer coupler lever to come all the way up without contacting the bottom of the bike rack or spare tire carrier receiver.
by: Tampa Doug10/15/2016
Maximize fun with this accessory! Made kayak trailer towing with a hitch mount bike rack easy and efficient.
Tampa D.
10/15/2017
Working great. Still going strong.
by: Ned08/10/2015
I originally thought this would work for a pop up camper and adding the bike rack. We have a Thule rack with a Jayco camper. It does not work at all for this set up. However, the product is excellant quality and delivery was prompt. I would recommend it for some other type of set up but not what I described above. I have to send it back.
Tom
9/1/2015
Does this not work due to the turning problem with the bikes coming in contact with the trailer or propane tank? I was thinking of getting this but not if that is the problem.
Rachael H.
9/1/2015
The effectiveness of the Curt Multi-Purpose ball mount # D210 used for both hitch mounted accessories is dependent on the configuration of the trailer, cargo on the trailer, and the hitch mounted accessories. Using this with a bike rack is always interesting and you have to account for the hitch location on the towing vehicle, the configuration of the bikes, and the trailer set up. It is very easy for turning radius to be effected by all of these things. We do have other options such as towing bike racks and trailer mounted bike racks that you might consider. I have provided links to both of these product categories for you to view and see what may work best for your specific application.
by: Deborah04/11/2018
This worked perfectly for me to haul my small pop up camper and my bike rack. It is very sturdy and easy to install and remove. I usually take it off at the campground so I can get my other supplies out of the back of my SUV without knocking my shins on it.
Deborah
4/11/2019
I still use this and love the ability to take both my camper and bikes this way.
by: Wesley 09/12/2023
Perfect fit Excellent finish
25
220
Show More Reviews
See what our Experts say about this CURT Trailer Hitch Ball Mount
- 5th Wheel Hitch Recommendation for a 1999 Chevy Dually Truck with 8 ft BedSince you have an 8 foot bed in your 1999 Chevy Truck you would need to install a stationary hitch in the bed of your truck. Nothing special required at all. First lets start with a rail kit though, for that I recommend the Reese Rail Kit part # RP30035. Installation instructions and video attached. For a hitch I would recommend the Pro Series 5th Wheel Hitch part # RP30928. This hitch has plenty of capacity and won't break the bank.
view full answer... - Choosing a Ball Mount with the Right Drop to Tow a Trailer Level with a 2004 Chevy TahoeSince you had them measure to the top of the coupler and not the bottom, the trailer will actually be a little lower than the vehicle by however tall the coupler is from the point they measured it. Those rental trailers are usually fairly low too. But since nothing is certain the best option is an adjustable ball mount such as # MT70068 rated for 5,000 pounds. This ball mount has a maximum rise of 6-1/4 inches, minimum of 1-3/4 inches, and maximum drop of 7-1/2 inches, minimum of 3 inches....
view full answer... - Solutions for Towing Trailer and Carrying Bike RackTowing a trailer and carrying a bike rack is possible but sometimes it can be a bit difficult. The best ball mount option is the part # D210 which gives you a ball mount platform and then a hitch opening above it for the bike rack. A slightly difference approach is the part # CC-275 which installs on the frame of the trailer and gives you a hitch opening to mount a bike rack.
view full answer... - Cargo Weight Capacity for Hitch Carrier Used in Curt D210 Multipurpose Ball MountYour 2007 Jeep Grand Cherokee can be fitted with any of three classes of aftermarket trailer hitch, either a 1-1/4-inch Class I or Class II, or a 2-inch Class III hitch. All available hitches for your car are shown on the linked page. You can refer to your hitch's safety sticker to confirm its Class rating. The linked article on hitches may be of interest too. The Curt # D210 Multipurpose Ball Mount fits 2-inch hitches like # 75338 and provides a 750-lb total tongue weight (TW) rating....
view full answer... - Can Curt Multipurpose Ball Mount D210 Handle Weight of Moped, Carrier and Trailer Tongue WeightThe Curt Multipurpose Ball Mount # D210 allows towing a trailer at the same time that a 2-inch receiver-mounted accessory is used, such as a scooter carrier for your moped. The key is that the Winnie's frame and the specific hitch that is installed have to have a tongue weight (TW) capacity that is high enough for the combined weight of the moped, the carrier and the trailer's actual tongue weight. This ball mount itself has a 750-lb TW rating but this does not mean that the hitch or the...
view full answer... - Availability of a Multi-Purpose Ball Mount with At Least 6,500 lb CapacityWe do have the Curt Multipurpose Ball Mount, # D210, that has a towing capacity of 7,500 lbs, tongue weight capacity of 750 lbs and receiver capacity of 350 lbs. This ball mount has a drop of 2-1/4 inches. At this time we do not have a dual purpose ball mount with a 5 inch drop ball mount platform. You can see all of the dimensions of the Curt multipurpose ball mount in the photo I linked for you.
view full answer...
- How to Use 6" Drop Ball Mount and Hitch Bike Rack on 2017 Chevy TahoeI have an alternative solution for you but it will look a little different than the Curt Multipurpose Ball Mount # D210 as the 2" drop you're seeing is pretty standard. To tow your trailer and carry your Thule bike rack I recommend checking out the Replacement Shank for Gen-Y Adjustable Ball Mount # 325-GH-204 which gives you the upper receiver as well as a 5" drop for the lowest receiver. If you have a ball mount with a 1" drop then that's what you'll use for this application, otherwise...
view full answer... - Compatibility of Hitch Accessory with Curt Ball Mount D210The Curt Multipurpose Ball Mount with 2-Inch Receiver # D210 will fit the hitch on your 2002 Infiniti QX4 as long as that hitch is a 2-inch Class 3 type like the Curt # 13088 or one of the others shown on the linked page. I linked an article to help you identify your hitch type. Installed in such a compatible hitch this multi-purpose ball mount provides a 2-inch receiver opening for using a 2-inch hitch-mount accessory. Keep in mind that the hitch (and the vehicle itself) must be rated...
view full answer... - Solution to Carry E-Bike Rack While Towing Malone Kayak TrailerI have a solution for you but it's a little outside of the box because the roof bike racks don't have the capacity for the heavier e-bikes like what you have. So instead what I would recommend is the Curt dual hitch adapter part # D210 which would allow you to carry a bike rack in the upper hitch opening and then use the ball mount platform to tow the trailer. Then for a bike rack the Swagman E-Spec part # S94FR would be a great option that uses frame clamps that are compatible with the...
view full answer... - Fit of Curt D210 Multipurpose Ball Mount With C13240 Class III Hitch on 2016 Hyundai TucsonYou can easily determine if the # D210 will fit. Locate the hitch pin hole, and measure rearward from the center of the hitch pin hole until you clear the furthest rearward edge of the back bumper. If this distance is less than 5 inches, the # D210 will work just fine for you. When we installed the Curt Class III hitch, part # C13240 on a 2016 Hyundai Tucson, we found the hitch pin hole to rear of bumper measurement to be 3-1/2 inches, which means the # D210 would work perfectly.
view full answer...
- Bike Rack Recommendation for use on a KZ23 CFK Hybrid Travel TrailerI pulled up some pictures of your KZ23 CFK hybrid travel trailer and it has an A-frame like what the part # CC-255 requires for installation, but the tip out portion of the trailer on the front would not be able to be used with the # CC-255 at the same. An easier to use route might be the part # D210 instead which is a ball mount that has a hitch opening above the platform. This would allow you to remove the bike rack from the hitch opening and use the tip out of your trailer. The most...
view full answer... - Adding a Trailer Hitch Receiver to a Bike RackI would not recommend adding a receiver to the end of the Swagman Original Towing Bike Rack, # S64675. This bike rack comes with a hole that allows you to add a hitch ball with a 3/4 inch diameter like part # 19256. If you want a 2 inch hitch ball, then you can use part # 19258. Adding a receiver would likely void the warranty on the bike rack. If you want to add a receiver because you need more of a drop or rise to tow your trailer level, then I recommend using a multipurpose ball mount...
view full answer... - Does Curt Multipurpose Ball Mount Reduce Towing Capacity The Curt Multipurpose Ball Mount # D210 referenced in your question is designed for exactly what you are wanting to do. The ball mount will allow you to hook up your T@B Camper and the top 2 inch receiver will work great for your Thule Bike Rack. Unlike a lot of similar adapters, this multipurpose ball mount does not actually reduce the tongue weight or towing capacity of your trailer hitch and tow vehicle. As long as you remain under the 500 pound tongue weight limit and 5,000 pound towing...
view full answer... - Carrying Bikes and Towing Pop-Up Camper Silmutaneously with 2015 Subaru ForesterIn order to carry bikes as well as tow, you'll first want to install a trailer hitch. Using a Class III hitch like the Draw-Tite # 75876 with the more common 2 inch receiver tube opening will provide you with the most flexibility in the future, as there's many more hitch accessories available for the Class III hitch. Even though you have a hitch in place, you could still use a trunk mounted rack, but I'd recommend a hitch mounted rack, because it'll be much easier to install and remove...
view full answer... - Options for Towing a Trailer and Carrying Bikes with a 2002 Subaru WRX WagonI wish they did, but the only ball mount/hitch opening products we sell are for 2 inch hitches like the part # D210. If you are looking to carry bicycles and tow a trailer you could install a roof rack and then go with roof rack mounted bike racks. For a roof rack you would want the Thule Evo Raised Rail Feet # TH710401 and 53" WingBar Evo Crossbars # TH711420. Then for a bike rack you could get the Thule Big Mouth part # TH598004 .
view full answer... - Towing a Trailer and Carrying Bikes at the Same Time with a 1997 Toyota Land CruiserWe don't have a front receiver that will fit your 1997 Toyota Land Cruiser but I do have some possible solutions for you. First, you could use a dual purpose ball mount # D210. This ball mount has a 2 inch receiver on the top so you could use it with your bike rack. The ball mount has a 750 pound tongue weight capacity but that is the trailers tongue weight and the weight of the bike rack and bikes combined. The receiver has a capacity of 350 pounds. So if your bikes and bike rack weigh...
view full answer... - Trailer Hitch and Bike Rack Scrape the Ground when Going Up Inclines with 2006 Honda OdysseyRoller # RM-050 is a good option for a Class III trailer hitch on your 2006 Honda Odyssey. It does hang down lower than the hitch receiver so it will actually make contact with the ground sooner than if the roller were not on it. This roller will not help with the Kuat bike rack though. What might work better is to use # D210 and put the bike rack in the upper receiver. This will raise it up higher and keep it from scraping on the ground, even if the hitch does scrape.
view full answer... - Can I Use # RM-077-2 to Tow Trailer and Carry Bike RackFlat towing is when you use a tow bar like # RM-501 and base plates like # BX2258 to tow another vehicle. Often our customers will tow their car behind their motorhome. I have included a FAQ article which explains flat towing for you to check out. We have several adapters that offer 2 receivers like the Roadmaster Dual Hitch Receiver Adapter, # RM-077-2, which you reference. You could also use Curt Multipurpose Ball Mount, # D210, which has a receiver on top and ball mount on the bottom. When...
view full answer... - Can A Cargo Carrier Be used as a Hitch Extension for Towing a BoatA cargo carrier like the Pro Series # 63153 you mentioned cannot be used as a hitch extender, primarily because the extended length would place too much leverage upon the receiver hitch and its mounting points. This excessive leverage would most likely damage the receiver and could cause the hitch to become detached from the vehicle. I would recommend using a Multi-Purpose Ball Mount like the Curt # D210. The ball mount is rated at 7500 lb towing, 750 lb tongue weight, and the receiver...
view full answer... - Multipurpose Ball Mount Recommendation to Tow a Boat and Carry a ScooterI have a solution for you, but the Roadmaster Dual Hitch Receiver Adapter # RM-077-4 that you referenced is only designed for flat towing vehicles so I cannot recommend it for you. Instead you would want the Curt Multipurpose Ball Mount part # D210. This will let you tow your boat with the ball mount and then use a carrier on the top hitch opening. The unit itself has a 7,500 lb towing and 750 lb tongue weight capacity while the top receiver has a 350 lb tongue weight capacity.
view full answer...
- How to Tow a Trailer with a Bike Rack Attached All of our dual receiver adapters like part # D-192 will reduce the vehicle's hitch capacity by 50%. As long as 50% of the vehicle's towing capacity in inline with your trailer and bike rack then this adapter will work well for you. However, a better option for you that will not reduce the vehicle's towing capacity would be to use multipurpose ball mount like part # D210. I have attached a review video of this adapter as well as a photo of it in use for you.
view full answer...
- High - Low Adapter for a Honda Odyssey Carrying a Bike RackThe product you selected, while seemingly being a match for your application will not work because it is made for applications with tongue weights of less than 100 pounds. Using this adapter would likely result in loss of the bikes and the rack. We do offer an option for your application though. The Curt Multi-Purpose Ball Mount # D2100 offers a receiver that is raised by 4-3/4 inches that would offer more ground clearance for your bike rack The unit has a 7500 lb towing, 750 lb tongue...
view full answer... - Front Mount Trailer Hitch for a 1998 Winnebago Chieftain Class A Motor HomeIf your Class A motor home is built on the Ford full size van E-350 or 450 chassis then you can install front mount receiver # 65001 that you have referenced. I have included a link to the installation instructions for you to view. If it was built on the Ford F-53 chassis then there are no custom fit front mount receivers available and you would need to have one custom fabricated by a qualified professional with knowledge of this type of custom project. We have some hitch fabrication parts,...
view full answer... - Recommendation for Using the Thule DoubleTrack Bike Rack When Towing a TrailerWe have 2 options that will allow you to tow a trailer and use a bike rack. The shank on the Thule Doubletrack Pro XT Bike Carrier, item # TH92BJ, is not designed, or large enough, to accept a draw bar for towing a trailer. The first option, and probably the best, is to use a towing bike rack like the Thule Hitching Post Pro Rack, item # TH934XTR. this rack will allow you to carry up to 4 bikes and tow a trailer as long as the weight of the bikes, bike rack and trailer do not exceed the...
view full answer...
Do you have a question about this Trailer Hitch Ball Mount?
Info for this part was:
Expert Research:
Jackie C
Expert Research:
Mike L
Expert Research:
Robert G
Expert Research:
Patrick B
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Adam R
Expert Research:
Lori W
Expert Research:
Jeffrey L
Video Edited:
Zack K
Video Edited:
Jacob T
Installed by:
Andrew K
Installed by:
Cole B
Installed by:
Shane T
Video by:
Joshua S
Video by:
Dustin K
Updated by:
Rachael H
Updated by:
Wilson B
Updated by:
Kristina F
Updated by:
Mike S
Updated by:
Isabelle B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
John
1/27/2024
I actually was never able to use it. It was bought to use with my car dolly and bike rack. It turned out the car dolly hitch was in the way of the bike receptor. So I have a brand new, never used receptor.