Customers compare LPL31CB to these similar products
Products Featured in this Video
Today on our trailer, were going to be installing the Optronics LED Mini Trailer License Plate Light with a two diode in chrome plated, part number LPL31CB. Were going to begin here by removing the existing license plate light, and in our case its broken up. Well go ahead and drill out each of the rivets. Now because the existing license plate light only had one wire on it, were going to go ahead… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
Great questions Jimmy, We haven't had any reports of the LED Trailer Tail Light w/ Reflector - Stop, Tail, Turn #DG52720PB having issues with hyper flashing so you should be good to go in those regards. When it comes to power draw, the tail…
view full answer...I have checked with my technical contact at the manufacturer and according to him, the specifications sheet, as well as their catalog the measurement B for Fulton Single Axle Trailer Fenders with Top and Side Steps #F008585-2 is indeed 6.7 inches. My…
view full answer...Replacing just the plunger portion of the Breakaway Switch #HM20010 is simple if you still have the plunger end. The plunger will simply reinsert into the switch, you may need to move the trailer to get the brakes to fully disengage as they will…
view full answer...The Fastway Zip Coiled Trailer Breakaway Cable w/ Plunger Pin - 6' Long item #FA80-01-2206 you were looking at is a universal replacement pin. It fits Fastway, Bargman and most other pin-style trailer breakaway systems. This part should fit but…
view full answer...When wiring a 2-wire license plate bracket, such as the Optronics LED #LPL55CB, you are correct that the white wire will be for ground and the black wire is used for the running lights. The white wire from the bracket should be attached to a clean,…
view full answer...The #STL22CCRB lamp you referred to is typically mounted in a grommet, like part #A70GB, which in turn is mounted in a bracket like part #337LB1SS. If you were planning on cutting a hole to mount the lamp and grommet, the hole will need to measure…
view full answer...I have included a link to the submersible license plate lights that we offer. If you are looking for an LED light, take a look at part #LPL91CB. I have included a short video for you.
view full answer...All of our 12 x 2-inch 6K-rated electric trailer brakes are shown on the linked page. Most of these use the 5-bolt mounting pattern but a few Dexter products include holes for BOTH bolt patterns, both 5-bolt and the 4-bolt Hayes/AL-KO pattern, parts…
view full answer...Yes, the Buyers Products 3/8" x 42" Trailer Safety Chain - 43 Proof #337BSC3842 has a max gross trailer weight (GTW) rating of 15,000 lbs, so it's going to be stronger than part #337B03835SC, which is a 3/8" x 35" safety chain…
view full answer...I would be happy to help you find the correct rated safety chains for your 15' car trailer, but you will need to confirm the GVWR (Gross Vehicle Weight Rating) of your trailer to be sure the chain is rated properly. For example the Curt Single…
view full answer...It should be getting close to 12 volts if the power output is set to the maximum on the brake controller. Some brake controllers will not work properly if they are titled or turned to the side or if it has a leveler knob that is not level. Check…
view full answer...When it comes to your 10,000 capacity trailer I recommend the Buyers Products Trailer Safety Chains #337B03822SC. They're made out of a zinc-coated steel. They're 22 inches long and the link diameter is 3/8 inches. I attached a review video…
view full answer...