What Size Hole to Mount Optronics 6-1/2 Inch Oval Taillight # STL22CCRB
Question:
Do you guys have a cut diagram or template that can be provided for what size hole to cut to mount the lights?
asked by: Dan
Expert Reply:
The # STL22CCRB lamp you referred to is typically mounted in a grommet, like part # A70GB, which in turn is mounted in a bracket like part # 337LB1SS. If you were planning on cutting a hole to mount the lamp and grommet, the hole will need to measure 6-3/4 by 2-1/2 inches, as you can see in the diagram I provided.
The easiest way to cut the hole would be to use a 2-1/2 inch hole saw, and cut two holes 6-3/4 inches apart (measured outside-to-outside). You could then use snips or a rotary tool to remove the materiel in the middle.
Products Referenced in This Question
Mounting Bracket for 6-1/2" Oval Trailer Tail Light - Stainless Steel
- Accessories and Parts
- Trailer Lights
- Vehicle Lights
- Mounting Hardware
- Brackets
- 1 Oval Hole
- Stainless Steel
- Buyers Products
more information >
PVC Grommet for 6-1/2" Oval Trailer Tail Lights
- Accessories and Parts
- Trailer Lights
- Mounting Hardware
- Grommet
- 6-1/2 Inch Long
- Oval
- Optronics
more information >
Product Page this Question was Asked From
Tinted Miro-Flex LED Trailer Tail Light - Stop, Tail, Turn - Submersible - 12 Diodes - Clear Lens
- Trailer Lights
- Tail Lights
- Stop/Turn/Tail
- Oval
- Recessed Mount
- Submersible Lights
- LED Light
- 6-1/2L x 2-5/16W Inch
- Red
- Optronics
more information >
Continue Researching
- Q&A: How to Cut a Grommet Hole for Installation of the Oval Trailer Tail Lights # STL22RB
- Q&A: Both Turn Signals Flash at The Same Time
- Shop: Right Angle 3-Wire Pigtail for Optronics Trailer Lights - 3-Prong PL-3 Plug - 10" Lead
- Shop: Mounting Bracket for 6-1/2" Oval Trailer Tail Light - Stainless Steel
- Shop: Tinted Miro-Flex LED Trailer Tail Light - Stop, Tail, Turn - Submersible - 12 Diodes - Clear Lens
- Video: Optronics Right Angle 3-Wire Pigtail Installation
- Video: Optronics Light Guide LED Oval Trailer Light Installation
- Shop: Optronics Trailer Tail Light - Stop, Turn, Tail - Submersible - Incandescent - Oval - Red Lens
- Shop: Optronics LED Trailer Tail Light - Stop, Turn, Tail - Submersible - 6 Diodes - Oval - Red Lens
- Shop: 3-Wire Pigtail for Optronics Trailer Lights - 3-Prong PL-3 Plug - 10" Lead
- Shop: Mounting Cover for 45-Degree TecNiq Mini LED Accent Light - Black
- Q&A: Installation of Hanger Brackets and Springs for Tandem Trailer Axles
- Video: etrailer Round A-Frame Trailer Jack Review
- Video: Choosing the Right Trailer Wiring
- Video: Review of Peterson Trailer Lights - Clearance Lights - M169-3R
- Shop: Trailer Wiring
- Search Results: vehicle lights
- Search Results: trailer hitch wiring
- Search Results: reflective tape
- Search Results: tounge jack
- Search Results: trailer plug
- Q&A: 7-Way RV Trailer Connector Wiring Diagram
- Video: Dexter Axle Trailer Hubs and Drums - Hub with Integrated Drum - 8-389-81UC3 Review
- Q&A: Replacement Trailer Hub and Drum Assembly for Dexter 8-389-91
- Q&A: Does the Bearing Come Already Installed in Trailer Hub and Drum Assembly, # 8-389-81UC3
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: trailer jack
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Hitch
- Video: Choosing the Right Brake Controller
on Trailer Lights
