Customers compare 8-173-16UC3 to these similar products
Products Featured in this Video
Today were going to review part number 8-173-16UC3. This is the Dexter Trailer Hub and Drum Assembly for electric brakes on a 2200 lb axle. This Dexter Trailer Hub and Drum is designed for 2000 lb trailer axles with electric brakes. The drum size is a 7-inch by 1-3/4. This will work with the part number 23-47 and part number 23-48 electric brake assemblies. This hub will only fit with the… see more >
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Videos
Help Articles
Expert Answers
The largest wheel and tire combo we offer that has a 4 on 4 inch bolt pattern and a pilot diameter of 2.5 inch is the Kenda 205/65-10 Bias Trailer Tire with 10" White Wheel #AM3H410 which has an overall diameter of 20.6 inches.
view full answer...You can absolutely get a 7-way connection at the back of your 2022 Subaru Outback Wagon. The reason you are only seeing 4-way adapters is because your Outback Wagon does not have factory wiring. So essentially you will need to install a 4-way flat…
view full answer...To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…
view full answer...We do have everything you need to install a 7-Way on your 2020 Subaru Outback Wagon so you can utilize a brake controller but we need to start off by making sure you have a 4-Way for the basic trailer lighting functions. If you don't already have…
view full answer...The 4-way trailer wiring kit I recommend for your 2018 Subaru Outback wagon is the Tekonsha kit part #118467 because it installs very easily and has the most reliable converter box of all of the kits we offer. This means it will be less likely to…
view full answer...A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
view full answer...Bearing Buddies like #BB2441 fit very tight into a trailer hub. In order to get them out, you will need to use a rubber mallet and persuade them out. Once the Bearing Buddy starts to unseat from the hub you can grab it and wiggle it out.
view full answer...Absolutely, in order to install a 5 bolt brake mounting flange, you will need the Brake Mounting Flange for 3" Round Axle part #4-44-1. This brake flange bracket is designed to work with an axle diameter of 3". If your axle is smaller than…
view full answer...That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…
view full answer...The Bearing Buddy Bearing Protectors #BB2441 provide premium protection for your wheel bearings. It is still recommended that you inspect the bearings, races, and seals every 12 months or 12,000 miles to ensure reliable performance on your trailer.…
view full answer...I reached out to my contact at Dexter Axle and she said that the Dexter Electric Trailer Brake Kit #23-47-48 have a coil resistance of 3.9 ohms per magnet. When it comes to wire size we recommend at least 10 gauge wire like part #10-1-1 (sold by the…
view full answer...To best level your 2016 Ford Expedition with your camper hooked up I recommend using a Equal-i-zer Weight Distribution System #EQ37100ET. This system will accommodate trailers with a tongue weight of 600-1,000lbs and a maximum trailer weight of…
view full answer...