Availability of 9/16 U-bolt With 2-1/2 Inch Inside Dimension By 7-1/2 Inches Long

Question

Question:

I am looking for axle u-bolts that measure -9/16 in diameter x 2-1/2inch inside width x 7-1/2Long or longer. Do you carry these? Part #? Thanks.

asked by: Darryl M

0

Expert Reply:

I don't have an exact match, but part # 175668 should work just fine for you. The U-bolt is designed for 2-1/2 inch axles, and has an inside dimension of 2-5/8 inches. The bolt is 9/16 in diameter and is 7-3/4 inches long.

expert reply by: Mike L

0

Answer 1

We do offer axle beams alone and also complete axle kits that include hub/drums, brakes etc. All can be viewed by clicking on the included link. I also was unable to find a cross-reference for your axle number 4330537. This may be a production code…

view full answer...

Answer 2

The U-bolts on a trailer suspension are designed to attach the leaf springs to the axle of the trailer. The U-bolts will need to fit the diameter of your axle. I would recommend to measure the diameter of the axle. A 6,000-lb axle should have a…

view full answer...

Answer 3

I do have a few easier options for you to determine the weight capacity of an axle other than using the bolt pattern or the number of lug nuts. The problem with using the bolt pattern to tell the axle capacity is that an axle may have the a bolt…

view full answer...

Answer 4

Since your axle's tag cannot be read to confirm its weight capacity we can help you estimate this by comparing the weight ratings of springs similar to yours. This will not necessarily be exact but it will get you in the ballpark. Thank you for…

view full answer...

Answer 5

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 6

The 14-1/4 by 14-1/4 is the standard opening for a roof vent or vent fan, so the MaxxFan #MA00-06401K would be a great choice to replace your existing fan. The inside of the vent units usually measure 14 x 14, so everything will fit perfectly for…

view full answer...

Answer 7

There really isn't a solution we can provide aside from replacing the spindle since yours is damaged beyond repair. Since you have a 3,500 lb EZ lube axle the correct replacement spindle would be the part #TRU74FR. I recommend taking it to a shop…

view full answer...

Answer 8

I reached out to my contact at Dexter and based on your serial number, they can't really narrow it down. It is an older axle that was produced in a plant that has since been closed. All they can tell me is that it is between 2K and 8K capacity…

view full answer...

Answer 9

I reached out to my contact at Dexter and they don't have any information based on that serial number in their system. They recommended taking off one of the wheels and on the hub there will be a number that starts with 8 followed by a dash and…

view full answer...

Answer 10

If you can read me the serial number on the axle I can then call the manufacturer, Dexter, and find out the weight capacity but if not you can measure the diameter and use the chart below to determine axle capacity. The "P16" is the plant…

view full answer...

Answer 11

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 12

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Availability of 9/16 U-bolt With 2-1/2 Inch Inside Dimension By 7-1/2 Inches Long

Product Page this Question was Asked From

Continue Researching