What is the Mounting Hole Spacing for Motorhome Hitch 5350

Question

Question:

I want to replace a Reese receiver with the 5350 more towing capacity. Where can I find out the mounting bolt pattern? Im hoping to luck out and not have to drill new holes. Thanks

asked by: Mike R

0

Expert Reply:

Motor home hitch # 5350 features two holes on each side bracket for mounting the hitch to your frame.

The bolt holes are spaced 8-5/8 inches apart, center to center, and are 1/2 of an inch in diameter.

I have included a link to the installation instructions for the hitch.

expert reply by: Sarah L

0

Answer 1

From the top of the mounting brackets to the top of the crosstube on the Curt Adjustable Width Trailer Hitch Receiver for RVs #C13702 measures about 2" and then from the crosstube to the end of the receiver measures about 6". I have…

view full answer...

Answer 2

The distance from the two bolt holes on each side bracket for the Curt Adjustable Width Trailer Hitch Receiver #C13702 is right at 8-5/8" (center to center). I have also attached a diagram to assist. This adjustable hitch will fit frame widths…

view full answer...

Answer 3

The Adjustable Width Trailer Hitch Receiver for RVs, 22" to 66" Wide #C13704 has brackets that are 10 inches long with mounting holes 8-1/2 inches center on center. The height is right at 5-1/2 inches tall. I've attached a video to…

view full answer...

Answer 4

From side to side, the mounting holes measure 31-1/4 inches apart, center to center. All three sets of holes are the same distance apart. From rear to front, beginning at the rear of the vehicle the distance from the first set of holes to the second…

view full answer...

Answer 5

From the forwardmost edge of the mounting bracket back to the face of the hitch receiver is going to be about 13-3/4" for the Adjustable Width Trailer Hitch Receiver #C13702 you're looking at.

view full answer...

Answer 6

I went out to the warehouse and measured Curt trailer hitch #C13704 for you. The distance from the top of the mounting flanges to the top of the cross tube is 2 inches. I have included some pictures with additional measurements for you.

view full answer...

Answer 7

As we have not had a 1973 Ford F-100 in our shop to test fit the available receivers I can only give you the measurements from one of our receivers so that you can see where it will sit on your truck. The Curt Trailer Hitch Receiver #C14082 is…

view full answer...

Answer 8

The side support brackets of the Multi-Fit Motorhome Trailer Hitch, 24 - 46 inches wide #5350 have a measurement of 8.62 inches center to center. This hitch has the extra hole for stabilization. I recommend using the #63232 to add stability to your…

view full answer...

Answer 9

The distance between the bolt holes from side-to-side on the Buyers Products Hitch Plate with Receiver Tube #3371809067 are 35.05 inches apart. The height of the mounting flange is 6-1/2 inches. The distance between the bottom of the flange to the…

view full answer...

Answer 10

I spoke to my contact at Curt and he informed me that the Curt hitch #C15317 center section measures 31-5/8 inches. The center to center mounting hole width with the flanges attached is 34-7/8 inches. He also informed me that the flanges on the…

view full answer...

Answer 11

The Curt Trailer Hitch Receiver part #C15400 and the Curt Trailer Hitch Receiver part #C15800 are the exact same trailer hitch save for one has a 2" receiver tube opening and the other a 2-1/2" receiver tube opening. The dimensional drawing…

view full answer...

Answer 12

I went out to the warehouse to take some measurements of Curt trailer hitch #C14082. I made a picture showing the measurements for you. The bolt holes, starting from the one furthest forward on the vehicle, measures 2-3/4 inches to the center of the…

view full answer...