What is the Thread Pitch for Trailer Hub Wheel Stud Part # RG03-060

Question

Question:

What is the thread pitch for the stud RG03-060

asked by: Chuck

0

Expert Reply:

The threaded pitch of trailer hub wheel stud # RG03-060 is 20 threads per inch and the diameter is 1/2-inch. See diagram to the right.

expert reply by: Chris B

0

click to enlarge

Answer 1

Based on the measurements you have provided it sounds like you have pretty standard wheel studs. Kodiak stud #K12WB2 is nearly spot-on as far as the measurements. I have included a picture showing its measurements for you.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 4

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 5

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 10

You can add larger wheels and tires to a trailer as long as you have enough room for the larger size. The main clearance issues we find when putting larger tires and wheels on a trailer is from the top of the tire to the fender and from the inside…

view full answer...

Answer 11

Your math is correct in your trailer weight load example. If a fully-loaded tandem axle trailer weighs 4000-lbs then each of the 4 tires will bear 1/4th of that load, or 1000-lbs. In this case a tire rated for 1300-lbs would provide a good safety…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

What is the Thread Pitch for Trailer Hub Wheel Stud Part # RG03-060

Product Page this Question was Asked From

Continue Researching