Replacement Hitch Hardware for Draw-Tite # 36520 and Wiring Harness for 2014 Honda CR-V

Question

Question:

Hello, is it possible to buy just the installation hardware for this hitch: Draw-Tite Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4inch - Honda CR-V, 2014? Also, do you sell the necessary wiring harness for the 2014 Honda CR-V? Thank you.

asked by: Matt W

0

Expert Reply:

Yes! We can help you with both of these items.

Replacement hitch hardware can be ordered by itself simply by entering the part # RHK into our search box, and then entering the hitch part # 36520 and selecting Draw-Tite from the drop-down menu. I have linked you to two helpful hitch installation articles as well as to an install video. The hitch installs without drilling or welding.

The recommended ball mount for use with this hitch is part # 36051; with this ball mount you can use either hitch ball # 19258 for a 2-inch ball or part # 19256 for a 1-7/8-inch size ball.

The correct wiring harness for your 2014 Honda CR-V is part # 118561 from TowReady. An installation video link for this item is also provided at right, along with the written instructions.

expert reply by: Adam R

0

Answer 1

The Curt Class II trailer hitch you referenced, part #C12038 has a 3500 lb towing/350 lb tongue weight capacity. If you'll only be using the hitch for towing a trailer, it should work just fine for you. However, if you're wanting to…

view full answer...

Answer 2

I have a solution, however the Master Lock Hitch Receiver and Coupler Latch Lock Set #2848DAT does not offer a 1/4" only kit. What we do have is the Trailer hitch Receiver Lock #5200 is a single lock that will fit 1 1/4" x 1…

view full answer...

Answer 3

For the Curt hitch #C11416 the recommended ball mount is #C45521 which is 7-1/4 inches long. So as far as length goes the average on the recommended mounts is about 7 inches but it can be longer. The rise on these recommended ball mounts…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 6

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 7

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 8

You can get a new brake mounting flange for your axle. The old flange will need to be cut off. The part is #4-44-1. This is designed to fit a 3 inch trailer axle and should be welded in place by a professional. Since you would also have to get the…

view full answer...

Answer 9

We do have 205/75R14 size radial tires that have a load range of D and a speed rating of at least 81 mph. Out of our available selection I recommend going with the Kenda Karrier #AM10235. This tire has a max load rating of 2,200 lbs at 75 psi and a…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In regards to the Correct Track Trailer Alignment and Lift Kit part #RR23QX, the kit provides a lift by essentially extending the hangers. This normally requires cutting off the old hangers and welding on new, taller ones but with this kit you…

view full answer...

Answer 12

The Correct Track Trailer Alignment and Lift Kit part #RR23QX offers a 1-1/4" or 2-1/4"lift so if the hitch height height is lower than the vehicle hitch height you can use this kit to bring the trailer level with the vehicle and eliminate…

view full answer...