Installation Instructions for Curt Trailer Hitch # C11756 on 2007 BMW 3-Series Sedan

Question

Question:

can you email me install instruction for hitch product code: C11756 Curt Trailer Hitch for the BMW 3 Series, 2007 Thank you

asked by: Isac M

0

Expert Reply:

The Curt trailer hitch receiver you referenced, their 1-1/4-inch Class I hitch # C11756, is a correct fit for the 335i and 335xi sedans with gasoline engines. The hitch installs without drilling using included hardware. At right you will find a link to the installation instructions for this hitch receiver.
I have also linked for you two articles with helpful general tips for hitch installation.

Please note that this light-duty hitch has a tongue weight capacity of 200-lbs and maximum trailer weight rating of 2000-lbs. Your BMW sedan may have different weight ratings so it is appropriate to check your owner's manual (or with your local dealership, using your VIN number) to confirm the vehicle's tongue weight and towing capabilities. The lower of the two ratings becomes the overall limit for the system.

Curt requires that any non-trailer load, such as a bike rack or cargo carrier, be supported by their stabilizing strap # 18050. This is a requirement for maintaining the limited lifetime warranty coverage on the hitch. The strap is not needed when towing a wheeled trailer of any type.

If you do plan to use an accessory item such as a bike rack or cargo carrier do please note that you need to select a compatible Class I type to work with this hitch. Bike racks are limited to a 2-bike capacity when used in a Class I hitch. Please see the linked article on hitch classes for additional guidance and information on hitch capacities.

You will find at right links to our pages for Class I bike racks and Class I cargo carriers that are compatible with this Curt hitch.

expert reply by: Adam R

0

Answer 1

Yes you can install the Hopkins Insight brake controller in your 2021 Ford Ranger and actually you don't need anything else to do so. Your Ranger doesn't have a connector for brake controller wiring and instead has 4 blunt cut wires that are…

view full answer...

Answer 2

I've linked the installation instructions for the Curt #C11756. The hitch is compatible with a 335i sedan, non-Diesel model. If you were planning on using the hitch for towing purposes, you'll also need the trailer wiring harness, part…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Installation Instructions for Curt Trailer Hitch # C11756 on 2007 BMW 3-Series Sedan

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching