Replacement Vent Cover for 1994 Jayco Eagle Travel Trailer

Question

Question:

What is the model number for vent covers for a 1994 Jayco Eagle Travel trailer? I would like to purchase the best available covers for my trailer. Thank you.

asked by: Joseph

0

Expert Reply:

We offer a range of complete trailer vent assemblies, such as the Ventline # V2092SP-28 that you referenced, as well as replacement vent covers in various materials and colors. The Jayco website does not provide specifics as to the vent supplied with your trailer but typically trailer vents are a standard size intended for 14-1/4 x 14-1/4 roof openings.

You can select a replacement vent cover using the link provided. This will take you to our main page for trailer vent lids and you can use the filters in the left-hand margin to select the type of hinge used on your vent. Replacment covers are available in three hinge types: 3-point, 4-point and continuous hinge. You can click on the filters to narrow the results by hinge type, material and color to find the one you need.

If you cannot find the cover you need a second link is provided to show you all complete vent assemblies that we offer.

expert reply by: Adam R

0

Answer 1

I went out to the warehouse and pulled a MaxxAir Vent 64643 and a Ventline Ventadome Trailer Roof Vent, #V2092SP-28, and tested them together. The MaxxAir fits over the Ventline vent so the two are compatible. The MaxxAir cover was designed to fit…

view full answer...

Answer 2

It sounds like you are talking about the ceiling garnish. I have included a link to the ones that we carry to the right. But they are all 14-1/4 inches square. This is the measurement of the part that fits in the opening though, not the overall…

view full answer...

Answer 3

The fan itself only fits onto the motor one way. If you wanted to reverse the rotation of the fan you would need to switch the positive and negative leads on the back of the motor. I tried this with just the motor and it will reverse the rotation.…

view full answer...

Answer 4

The interior trim piece on the Ventline Trailer Roof Vent, part #V2092SP-28, fits roofs 1-7/8 inches to 3 inches thick. This unit should work just fine for you. I have included a link to a video review of the vent for you.

view full answer...

Answer 5

I went out to the warehouse and the thickness of the rough opening in the roof for installing this vent can be from 1-7/8 inches to 3 inches.

view full answer...

Answer 6

The Ventline Ventadome Trailer Roof Vent #V2094SP-30 that you referenced is an exhaust fan, what that means is that it pulls air out of the the trailer. The reason for this is that hot air rises, so when you pull out the air at the top of the…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 10

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 11

Thanks for the pictures of your roof vent lid Marty! Based on that the correct replacement is the Ventline part #BVD0449-A01 that you referenced if you wanted white or the part #BVD0449-A03 for the same smoke color you have now.

view full answer...

Answer 12

Hey Paul, we have a Blue Ox base plate kit that fits your 2024 Nissan Versa with the part #BX1856. In addition to the base plates, you will also need a compatible tow bar, safety cables, lighting, and supplemental braking to flat tow your vehicle.…

view full answer...