Depth of RV Roof Mount Vent for installing through the roof

Question

Question:

How deep is the vent? I need to know if it can make it through the roof, and plywood runner in the top of my trailer.

asked by: Jason

0

Expert Reply:

I went out to the warehouse and the thickness of the rough opening in the roof for installing this vent can be from 1-7/8 inches to 3 inches.

expert reply by: Robert G

0

Answer 1

The fan itself only fits onto the motor one way. If you wanted to reverse the rotation of the fan you would need to switch the positive and negative leads on the back of the motor. I tried this with just the motor and it will reverse the rotation.…

view full answer...

Answer 2

The Ventline Ventadome Trailer Roof Vent #V2094SP-30 that you referenced is an exhaust fan, what that means is that it pulls air out of the the trailer. The reason for this is that hot air rises, so when you pull out the air at the top of the trailer…

view full answer...

Answer 3

I went out to the warehouse and pulled a MaxxAir Vent 64643 and a Ventline Ventadome Trailer Roof Vent, #V2092SP-28, and tested them together. The MaxxAir fits over the Ventline vent so the two are compatible. The MaxxAir cover was designed to fit…

view full answer...

Answer 4

We offer a range of complete trailer vent assemblies, such as the Ventline #V2092SP-28 that you referenced, as well as replacement vent covers in various materials and colors. The Jayco website does not provide specifics as to the vent supplied with…

view full answer...

Answer 5

The interior trim piece on the Ventline Trailer Roof Vent, part #V2092SP-28, fits roofs 1-7/8 inches to 3 inches thick. This unit should work just fine for you. I have included a link to a video review of the vent for you.

view full answer...

Answer 6

It sounds like you are talking about the ceiling garnish. I have included a link to the ones that we carry to the right. But they are all 14-1/4 inches square. This is the measurement of the part that fits in the opening though, not the overall width…

view full answer...

Answer 7

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

Thanks for the pictures of your roof vent lid Marty! Based on that the correct replacement is the Ventline part #BVD0449-A01 that you referenced if you wanted white or the part #BVD0449-A03 for the same smoke color you have now.

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Depth of RV Roof Mount Vent for installing through the roof

Product Page this Question was Asked From

Continue Researching