How Does the Curt Hitch part # 13390 Install on a 2010 Subaru Outback Wagon

Question

Question:

Is it possible to attach this hitch from the spare tire well inside the trunk versus working under the car? Thanks.

asked by: Matt P

0

Expert Reply:

The only way to install the Curt Hitch part # 13390 is to attach it to the rear frame rails of your 2010 Subaru Outback Wagon. See the picture I attached as well as the install video.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I do have a solution for you, however the Draw-Tite QSP Trailer Hitch Silencer and Cover for 2" Hitch Receivers #63080 is specifically designed to work with Draw-Tite 2" x 2" trailer hitch receivers. Because the collars on…

view full answer...

Answer 2

It is very unlikely that the hitch pin hole on your Draw-Tite Trailer Hitch Receiver is worn causing the ball mount to slide back and forth. There is usually a little bit of play in the receiver tube opening with a ball mount and this can easily be…

view full answer...

Answer 3

Yes, the 75673 hitch will carry over and fit the 2011 model Outback. We also have the Curt Trailer Hitch, #13390. This is a Class III trailer hitch rated at 3,500 pounds of gross trailer weight and 350 pounds tongue weight capacity, and it has a 2…

view full answer...

Answer 4

We have just what you're looking for with the Gen-Y Anti-Rattle Clamp for 2" Hitch Receivers #GY88XR. The sleeve acts as a wedge to take out play between your hitch receiver and extender. Although it does not not require a wrench and…

view full answer...

Answer 5

The Draw-Tite #75673 hitch has a higher towing capacity than the Curt #13390, but because the vehicle itself is limited to 2700 lbs towing/200 lbs tongue weight, the higher hitch capacity would not be usable. The Curt hitch is less expensive, but…

view full answer...

Answer 6

For your 2016 Subaru Legacy Sedan, I recommend going with a Class III trailer hitch. While you may not ever need the higher rated weight capacity of a Class III hitch, the 2 inch receiver opening will allow you to choose from many more hitch-mounted…

view full answer...

Answer 7

I am not sure what you mean. The hitch itself should not be swaying at all. If you are talking about trailer sway while towing then the aerodynamic differences between the vehicles could the reason for the trailer to sway more with one vehicle than…

view full answer...

Answer 8

Each hitch is positioned to sit tucked up and close to the bumper as you can see on the product page pictures. All of the hitch receivers available for the 2011 Subaru Outback will sit in the same general position with ground clearance varying…

view full answer...

Answer 9

In a towing setup your towing capacity is always the lowest rated component as that is the weakest link. The hitch manufacturers we carry like to make hitches that are a bit stronger than needed but that does not give the vehicle any more towing…

view full answer...

Answer 10

For a 4.80-12 trailer tire, the overall diameter or height is 20.5 inches. For a 5.30-12 it is 21.9 inches. That is a difference of 1.4 inches but you will only see half of that, 0.7 inches, in added height. Please keep in mind that going to a taller…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

How Does the Curt Hitch part # 13390 Install on a 2010 Subaru Outback Wagon

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching