What Spindle is Needed for LM67048 Inner and LM11949 Outer Bearings

Question

Question:

i need a spindle .. i have inner bearing lm 67048.. the outter bearing is lm 11949.. it is on farm implement.. 5 on 5.5 bolt pattern. . the distance from inner bearing to outter bearing 3.5 inches .. thank you

asked by: jw

0

Expert Reply:

The spindle we show for the # LM67048 inner and # LM11949 outer bearing is the # TRU54FR Agricultural Spindle. We do not list the distance between the inner and outer bearing so I cannot verify that dimension for you. You can order the spindle, item # TRU54FR, using the link below if you like.

expert reply by: Robert G

0

Answer 1

The hub part #DX22XR matches the bearing numbers of your old hub so they will fit and work well.

view full answer...

Answer 2

The trailer hub part #DX22XR uses both bearing numbers you mentions of LM67048 and LM11949 and has a bolt pattern of 5 on 4-1/2 inch so it will fit. The bolt pattern would be different though so you'd need to find a new wheel and tire. I attached…

view full answer...

Answer 3

Tapered roller bearing #LM11949 is typically used in agricultural hubs and mates with race #LM11910. We do offer these parts the correct grease seals #CE16305A to match your dimensions but we do not offer any hubs that use this specific bearing as…

view full answer...

Answer 4

The hub face of the #AH15450ECOMP Agricultural Hub is 6-1/4 inches in diameter, and the overall depth is 4 inches. The hub has an inner hub bore diameter of 2.328 inches with an outer bore diameter of 1.781 inches. I've shown these dimensions in…

view full answer...

Answer 5

We don't carry any hubs at this time that use bearing #LM67048 for both the inner and outer bearings. We do have some that use #LM67048 as the outer bearing and two that do as the inner bearing. I've linked the selections for you. If you have…

view full answer...

Answer 6

It sounds like your existing hub uses a LM67048 inner/LM11949 bearing. The only hubs we offer that would be compatible with that bearing set would be an agricultural hub like #AH15450ECOMP which is meant for low-speed use (20 mph or less) on…

view full answer...

Answer 7

I have some possible solutions for your application, but the Trailer Axle with Idler Hubs #e25GR that you were looking at has the 60" long hub face length you're needing but the spring center distance is 48" which is a bit longer than…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...