Can Weld-on Bracket Kit # 4916 Be Bolted to a Frame

Question

Question:

Looking at the photos of this product, I see there are bolts holes in the flanges. Am I correct that the receiver tube gets welded but the flanges can be bolted to frame to provide the ~ 10inch ?

asked by: Andy

0

Expert Reply:

The Weld-on Bracket Kit # 4916 is meant to be welded on meaning the crosstube gets welded to the brackets and the brackets to the frame. The brackets went through a design change and may or may not have holes in them. Either way they are meant to be welded on, not bolted on.

expert reply by: Michael H

0

Answer 1

Thanks for the picture, and the measurements! I took a look at your bumper, and it doesn't appear that the Mount-n-Lock GennyGo Generator and Cargo Carrier for RV Bumpers #MNT54FR will be a good fit for you. This cargo carrier will fit square…

view full answer...

Answer 2

I checked with Draw Tite and the size bolt recommended for the mounting holes of the brackets #4916 is 5/8 inch which is the diameter of the holes.

view full answer...

Answer 3

The best option we have available for your 2008 Sterling Bullet Cab and Chassis is the Draw-Tite Ultra Frame Service Body Trailer Hitch #41991 paired with the 16" Weld-On Bracket Kit #4916. These extra long brackets will give you the drop needed…

view full answer...

Answer 4

The Curt Adjustable Trailer Hitch Receiver, Class III - 2", #C13701 that you link to, has a maximum gross trailer weight rating of 5,000 lbs. However, this is increased to a maximum GTW of 6,000 lbs. when used with weight distribution system. My…

view full answer...

Answer 5

We do not carry a hitch designed specifically for your 1996 Freightliner MT45 but we do have some universal hitches that may work for you. The Draw-Tite #41990-07 is a weld-on hitch that will fit frames up to 44 inches wide. Also, there's…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 12

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Can Weld-on Bracket Kit # 4916 Be Bolted to a Frame

Product Page this Question was Asked From

Continue Researching