Will Kodiak 13" Rotor Fit Dexter Hub on 8k Lippert Axle

Question

Question:

I have a 2008 mobile suites 5th wheel. The trailer came with lippert 8000 lb axles and Kodiak disc brakes with xl lube never Lube cartridge bearings and rotor. Rotor and hub are one pc. I was able to install a Dexter neverlube hub assembly on my lippert axle. Will this rotor be the right depth front to back to fit my caliper and will the center hub hole work with the Dexter hub?? Thank you!

asked by: Andy D

1

Helpful Expert Reply:

Yes, the Kodiak 13" Rotor # KR13858D will fit your Dexter hub and work with your existing Kodiak Calipers # KDBC250D. This is assuming you have an 8 on 6-1/2 bolt pattern, which I'm sure you do, and your wheel size is 16" or larger.

expert reply by: Robin H

1

Answer 1

Yes you can go the route you mentioned. You'd need to install an idler Dexter 8k Nev R Lube hub with part #004-402-90 on your spindles and then you could use a slip on kit like the part #K2R89DDE and you'd be set.

view full answer...

Answer 2

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular…

view full answer...

Answer 3

The AL-KO trailer hub part number 8700 that you have is a 3,500 lb trailer hub/drum with a 5 on 4-1/2 inch bolt pattern. Based on that the #AKHD-545-35-EZ-K is the correct fit and would work great.

view full answer...

Answer 4

We have a really great kit that comes with everything you'd need to convert your 2021 Vanleigh Pinecrest 335RLP from tandem 6k drum brakes to electric over hydraulic disc brakes with the HydraStar Disc Brake Kit w/ Actuator for Triple Axle…

view full answer...

Answer 5

The Shackle Strap part #TRSL350 comes as a single strap. There should be 2 shackle straps per spring on a single axle trailer. You would need to order 4 of the part #TRSL350 for a single axle.

view full answer...

Answer 6

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

I spoke to my contact at Kodiak about the issue you are having and he said that sometimes if a trailer braking system is doing way too much of the braking the pressure can get too high for the calipers and they can break (not brake). He said that the…

view full answer...

Answer 10

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 11

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Will Kodiak 13" Rotor Fit Dexter Hub on 8k Lippert Axle

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching