Torque Specs for the Installation Hardware for the Curt Hitch part # C13105

Question

Question:

I have a C13105 receiver on a 2013 Toyota Sienna XLE. I cannot find my installation instructions. Could you please provide the proper torque setting for the mounting bolts? Thanks,

asked by: Robb F

0

Expert Reply:

I attached a set of the installation instructions that has the torque figures listed for all the installation hardware.

I also attached an install video for you to check out.

expert reply by: Jameson C

0

Answer 1

The Curt #C13105 is indeed a fit for your Sienna. Here's how the exhaust can rattle against the hitch, even if the correct hitch has been installed. The exhaust system at the rear of the car is attached to the vehicle using rubber isolators…

view full answer...

Answer 2

I'd go with the Tekonsha #22119 if you think you might go with a different bake controller at some time in the future, but if you're happy with the Curt #C51180 Echo wireless brake controller, you can install a functional 4-pole using…

view full answer...

Answer 3

It sounds like you have corrosion compacted in the weldnuts on your 2009 Toyota Sienna. All you can do is spray the lubricant, let it sit from about 15 minutes, and then go at the weldnuts with a wire brush. Do this repeatedly. If that…

view full answer...

Answer 4

The Curt trailer hitch part #C13105 comes with all of the install hardware needed, but the bolts are size M12-1.25x40 hex. If you need the replacement hardware you would want part #RHK. If you enter the part number on this product page we will ship…

view full answer...

Answer 5

In all likelihood you will not have to tap the holes on your 2006 Toyota Sienna to get the hitch bolts to fit. Usually the issue is that the weld nuts on the vehicle will get packed with grime and corrosion and all you will have to do is clean them…

view full answer...

Answer 6

The Curt Trailer Hitch Receiver #C13105 that you referenced, which is confirmed to fit your 2018 Toyota Sienna, uses six M12-1.25 x 40 hex bolts and six 1/2 inch conical toothed washers for installation. We can indeed provide you with this hardware…

view full answer...

Answer 7

According to the instructions, the bolts for hitch part #75237, are M12 x 1.25 x 40MM bolts. If you do not have a metric tap and die set, I would just take one of the bolts to a hardware store and match the tap to the bolt.

view full answer...

Answer 8

The wiring harness I recommend for your 2008 Toyota Sienna is the Tow Ready T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector #118304. I recommend this custom wiring harness because it will offer the simplest installation. The…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Answer 12

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Torque Specs for the Installation Hardware for the Curt Hitch part # C13105

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching