What is the Tongue Weight Capacity of Draw-Tite Trailer Hitch 24805 for a 2009 Ford Focus

Question

Question:

What is the maximum weight for carrying not pulling?

asked by: Ron

0

Expert Reply:

The capacity you are looking for is the tongue weight capacity. Tongue weight is the term used for how much vertical load can be on the hitch. For trailer hitch # 24802 for your 2009 Ford Focus the tongue weight capacity is 200 pounds.

You will want to check the Focus owners manual to see if it has a tongue weight capacity. Whichever is lower, the hitch or the vehicle, that is the capacity you will need to go by. I have included a link to a video showing installation of the hitch and a link to the instructions for you.

expert reply by: Michael H

0

Answer 1

A draw-bar or ball-mount is the shank or piece that slides into the hitch opening that allows a hitch ball to attach to. Basically the hitch is the portion that bolts to the frame of the vehicle and then the draw bar is the metal shank that slides…

view full answer...

Answer 2

Either the Kuat Tranfer 1 #KU64FR or the RockyMounts MonoRail Solo 1 #RKY10007 would handle the bikes you describe easily. Both would hold the bikes by the tires, so the fact that the rack won't come into contact with the frame will work well…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...