Front Camper Tie-Down For 2014 Chevrolet Silverado 3500

Question

Question:

Can the camper tie downs be purchased separately, such a front only?

asked by: Cathy W

0

Expert Reply:

You sure can purchase the tie-downs separately. I have attached a link to our website product page for the tie-downs we have available for your 2014 Chevrolet Silverado 3500. Near the top of the page is a drop-down box you can make a selection based on the bed length, cab style, running boards, and whether or not you have a hitch installed on your Silverado. It will list both the front and the rear tie-downs that would be a fit for your vehicle.

When the page displays the front and rear tie-downs, you can scroll down the page to select the front tie-downs or the rear tie-downs. Then select the highlighted part number and you will be taken to the product page for that tie-down.

If you wish to let me know the cab style, bed length, hitch configuration, and type of running boards you have on your Silverado, I will be happy to help you with selecting the tie-downs that would work for you.

expert reply by: Jeffrey L

0

Answer 1

If your 2015 GMC Sierra 2500 has no steps or running boards and a factory hitch then I have the following options based on bed length and cab: 6-1/2' Bed - TorkLift Custom Frame-Mounted Camper Tie-Downs - Front #TLC2220 8' Bed (Crew Cab) -…

view full answer...

Answer 2

I can see how this is confusing, since our site often uses part numbers that differ from the manufacturer's part numbers, but the TorkLift #TL44FR is TorkLift part number- C2226 so that would be the correct front tiedown for your 2020 Chevy…

view full answer...

Answer 3

As long as the bed in your 2011 GMC Sierra 2500HD is not a double-wall and it is not a step side or dually then you can use the Brophy camper tie downs, #HSSF or the angled down ones part #HSAB that you referenced. I also recommend the hardware…

view full answer...

Answer 4

The TorkLift Custom Frame-Mounted Camper Tie-Downs #TLC4204 (front) and #TLC3212 (rear) will fit your dually 2011 Chevy Silverado 3500 Crew Cab with an 8 foot bed, cab-length running boards and a factory hitch. I have added a photo of these tie-downs…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 10

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 11

The proper extension for your setup would be the one that allows you to have clearance of your hitch mounted accessory and also allows you to still be able to pull the steps down. If the receiver tube sticks out past the camper too far then you will…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Front Camper Tie-Down For 2014 Chevrolet Silverado 3500

Product Page this Question was Asked From

Continue Researching