Hubs and Disc Brakes For a MagicTilt Boat Trailer With 6,000LB Axles

Question

Question:

I an looking to crossover some Magic Tilt trailer parts. I am looking to rebuild the trailer brakes on my boat trailer and also convert from drum brake to disc on the front axle. The Magic numbers are PD2550-L PF1102 PG1094 PG2033 PG5058 PY0215 PY1305

asked by: Mike D

0

Expert Reply:

The Dexter Trailer Idler Hub Assembly # 8-213-51UC1-EZ is what we have for the part number PD2550-L but you will need the Grease Seal # GS-2125DL to replace the larger seal in the kit. Each pair of hubs will use these Bearing Buddy Protectors # BB2441SS instead of the PF1102 which is for a different size hub bore. The Demco Hydraulic Brake Actuator # DM8164311 is the exact same as the part number PG1094. The DeeMaxx Disc Brake Kit # DE28YR will work in place of the PG2033. And these will bolt to the brake flanges without needing the adapter PG5058 or Fasteners PY0215 or nuts PY1305.

expert reply by: Bud M

0

Answer 1

The Kodiak Disc Brakes #KOD69FR will fit on 5,200lb axles which use the #42 spindle dimensions. This is the most commonly used size but depending on the age of your trailer you may want to inspect your spindle. It will have a grease seal landing…

view full answer...

Answer 2

It looks like you have certainly done your research in regards to the HydraStar Electric Over Hydraulic Actuator and the Titan BrakeRite EHB Electric-Hydraulic Actuator. In regards to repose time, this goes to the Titan BrakeRite EHB with a…

view full answer...

Answer 3

On a standard 5 bolt electric brake like the Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 7,000 lbs item #23-181, The bolt holes measure 3-7/8 inches from one corner to its diagonal counterpart. From hole to hole across the…

view full answer...

Answer 4

Knowing the weight capacity of your axles is a good first step in determining if the Electric Trailer Brake Kit - Self-Adjusting #AKEBRK-7-SA will fit your Logan 7903 LQ. You will also need to know the mounting flange bolt pattern on your axle,…

view full answer...

Answer 5

Yes, you can use the Dexter Electric Trailer Brake Kit - 12" - Left and Right Hand Assemblies - 7,000 lbs item #23-180-181 on your 5,200 lbs axle so long as you have a 5 bolt flange like the one linked in the diagram below. These brakes fit…

view full answer...

Answer 6

Though we do have the Bearing Buddy #BB2441T-SS that is a direct replacement for Tie Down's Turbo Lube oil baths, this will require you changing over to grease instead of oil. With that said, we do also have the Kodiak XL ProLube Kit…

view full answer...

Answer 7

I recommend to measure the inside diameter of your hub bore to switch out the oil bath caps with threaded Bearing Buddy Bearing Protectors. The closest we have to the 3.3 inches that would thread into your oil bath hub is Bearing Buddy Bearing…

view full answer...

Answer 8

The DeeMaxx Disc Brake Kit #DE28YR does not have the E-Z grease fitting, you'd want to take a look at the Kodiak Disc Brakes #KOD69FR instead. This brake assembly is the same thing as #DE28YR but also includes 2 hub-rotor assemblies with…

view full answer...

Answer 9

I would be happy to help you set up a disc brake system for you 2012 Tandem axle boat trailer. Let's start with an actuator you are going to want the Titan Zinc-Plated Brake Actuator - Disc - 2-5/16" Ball item #T4750800. This is a bolt on…

view full answer...

Answer 10

Yes the Dexter Trailer Idler Hub Assembly for 6,000-lb E-Z Lube Axles part #8-213-51UC1-EZ will work with the Timbren Heavy-Duty Axle-Less Trailer Suspension part #ASR35HDS05. I was able to confirm that they use the same bearings. The reason that…

view full answer...

Answer 11

I did some looking and found that the 46210 and 46845 hubs you currently have use the same #L68149 inner bearing and #L44649 outer bearing. However, as we do not carry the Tie Down Engineering Vortex hubs, I cannot say what all will fit them,…

view full answer...

Answer 12

You can view drum brake surge couplers for 2-5/16-inch balls by clicking on the linked page. Simply click on the filters to select the features you want, such as weight rating, bolt-on versus weld-on installation, and a-frame or straight tongue…

view full answer...