What Door Switches Are Needed For The Kwikee Electric RV Steps Control Module Lippert # 776367

Question

Question:

Can you tell me which door switch is correct for this Kwikee Electric RV Steps Lippert # 776367

asked by: Henry W

0

Expert Reply:

The Replacement Control Module 776367 # LC34AF does require a normally open switch. We have several of these to choose from depending on how you can install them on your door.

Rocker Switch with Door Sensor # LC369311
Magnetic Door Sensor # LC378054
Magnetic Door Sensor # LC375385
Magnetic Door Sensor # LC369299

expert reply by: Bud M

0

Answer 1

The Kat's Heaters Vehicle Interior Heater #KH37100 takes in cold air through the round port and exhausts warm air from its rectangular port. Please refer to the linked photo showing the direction of air flow. This unit has four screw-head…

view full answer...

Answer 2

I recommend using the Magnetic Door Sensor #LC374198 for your custom boat project. These sensors are safe to be used in wet conditions and being magnetic will allow you to place the wired sensor on either the door or frame where you plan to mount…

view full answer...

Answer 3

The Kat's Heaters Vehicle Interior Heater #KH37100 would definitely help keep the interior of a Mini Cooper warm during snowy weather, but it hasn't been tested to see if the rise in temperature would be enough to warm the top high enough to…

view full answer...

Answer 4

We have two options for a switch matching your 3/4" x 1/2" dimensions. For white you need the #37213645 and for black the #37212815. These have cutout dimensions of 0.745" tall x 0.5" wide and the actual switch dimensions are…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 7

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 8

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...