Replacement 7-Way For 2000 Dodge Durango

Question

Question:

Due to a prior rearend wreck of my 2000 Dodge Durango, I need to replace the plug on the end of my tow wiring. It appears it was a 7 way circle plug with flat prongs in it. Will this product work? It has to have have the dodge rectangle plug on wiring end. Hopefully my pictures might help explain.

asked by: Michelle

0

Expert Reply:

We do have a replacement 7-way kit that fits your 2000 Dodge Durango that has the square connector you mentioned as well with the part # HM42190.

expert reply by: Jameson C

0

Durango 7-Way Connector 2000
(click to enlarge)

Answer 1

The easiest way to get your 4-Way flat vehicle end to connect to your trailer with a 4-Way round is to remove the 4-way round from your trailer and connect the wires to a Draw-Tite 4-Pole Trailer End Connector, part #18004. This will give you a…

view full answer...

Answer 2

If it was a 4-pin connector with 5 wires then it is called a wishbone harness and would have 2 wires attached to the running light pin so you have one wire for each side of the trailer. Typically, on a 4-Way, the white wire is ground, brown is…

view full answer...

Answer 3

I'd recommend using some dielectric grease, like part #11755. Not only will the grease prohibit moisture from entering the connections and protect them from corrosion, it will make the connection easier to plug together or to separate.

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 9

If your trailer has 7 wires running all the way back to the brakes, then yes, you can tap into the existing wiring. Each of your new brakes will have two wires for the brake magnet. One wire is for 12 volt power to the brake magnets and the other…

view full answer...

Answer 10

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 11

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Replacement 7-Way For 2000 Dodge Durango

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching