Will The Drop Leg # LC405217 Fit The Lippert Tongue Jack On 2023 Grand Design Imagine XLS 22MLE?

Question

Question:

I have a 2023 Grand Design Imagine XLS 22MLE trailer with a Lippert Power Jack shown in the attached picture. I dont see any model number on the jack...? It does have a serial number: 2023-03-01947. The jack post is 2inch diameter. Will the LC405217 leg fit this post? Thanks!

asked by: James C

0

Expert Reply:

Yes, the Drop Leg # LC405217 will fit your Lippert Electric Trailer Jack # LC285318 on your 2023 Grand Design Imagine XLS 22MLE travel trailer.

expert reply by: Bud M

0

Lippert Tongue Jack On 2023 Grand Design Imagine XLS 22MLE
(click to enlarge)

Answer 1

Yes, I went out to the warehouse and test fit legs on the Lippert Power Stance Electric Trailer Jack #LC69VR and found that the Drop Leg for Lippert Power Jack #LC405217 is a compatible match. This drop leg will slide into the inside of the inner…

view full answer...

Answer 2

Yes, the Lippert Drop Leg part #LC405217 that you referenced does fit the Lippert Powered A-Frame Jack part #LC285318 that you have.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 6

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 9

I contacted the manufacturer about the lengths for these stabilizer jacks and have included the information they were able to provide me. The Ark Drop Down Corner RV Stabilizer Jacks #ARK34FR are 422 mm (16.6") collapsed and 600mm (23.6")…

view full answer...

Answer 10

The 8-14.5 tires are an older metric size no longer used today. Therefore, you would need to replace these along with the wheels in order to update them. In order to see if we have any options for you, we'd first need to determine the bolt…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

I definitely understand how safety chain capacities and determining exactly what chain rating you need for your trailer can be a bit confusing. To keep it as simple as possible, safety chain requirements state that the breaking strength of EACH…

view full answer...