Would Holes Need to Be Drilled in Boat Trailer Step to Install CE Smith Roller Guide Ons

Question

Question:

I have a ski boat trailer, where the guides need to go there is a long step next to the frame. I know I need to mount it on top but should I still 2 holes thru the step itself. I already purchased the rollers from you.

asked by: Brandon R

0

Expert Reply:

Unless you wanted to weld the uprights to your trailer frame above the step you would need to drill some hole in the step so that you can install the CE Smith Roller-Style Guide-Ons # CE27610 that you ordered.

expert reply by: Jameson C

0

Boat Trailer Step
(click to enlarge)

Answer 1

Hey Bruce, so the mounting studs of the Optronics LED Combination Trailer Tail Lights #TLL160RK that you referenced can be set exactly 4 inches apart so this light kit would work great as a replacement and would install easily. These are also LED…

view full answer...

Answer 2

The kit we offer that is the closest to what you listed would be the Waterproof LED Submersible trailer taillight set part #TLL160RK. These are a bit bigger than what you mentioned but in most cases would work just fine as a replacement. I attached a…

view full answer...

Answer 3

You are correct that the roller style guide-ons #CE27610 are not meant to support weight. But the boat brushing up against them is to be expected and they will work fine for that. A little bit of space like you said will help to make sure the boat…

view full answer...

Answer 4

You will want the boat to be close to touching the rollers on the CE Smith Roller-Style Guide-Ons #CE27610. Since the guide-ons are not meant to support weight you will want to place them so that they are fairly close to the boat but not too far.…

view full answer...

Answer 5

Yes, the CE Smith Roller-Style Guide-Ons for Boat Trailers - 15" Tall - 1 Pair item #CE27610 will work great with your 20' long boat. You will want to make sure your trailers frame is less than 3" wide x 4-1/4" tall. I have linked…

view full answer...

Answer 6

I do have an option for you but you are correct about the hardware that comes with the CE Smith Roller-Style Guide-Ons for Boat Trailers part #CE27610 not fitting your I-beam that is 5-1/2" tall and 3-1/2" wide. However, you can still use…

view full answer...

Answer 7

The CE Smith Roller-Style Guide-Ons for Boat Trailers #CE27610 measure 17-1/2 inches horizontally. It mounts on 3 inch frames and roughly 3 inches of it is a portion which cannot be adjusted to so you will have approximately 11-1/2 inches that you…

view full answer...

Answer 8

The CE Smith #CE27610 Guide-Ons work well on the back of the boat, but in quick moving water something that's actually self-adjusting like the ARK #AR74FR self-aligning boat trailer loading system which is spring loaded would actively guide your…

view full answer...

Answer 9

As you can see in the provided photo, the rollers featured on the #AR84FR Ezi-Guide is indeed spring loaded. Once the boat hull rolls over them, they'll move to accommodate the shape of the hull. I've linked you to a product description video…

view full answer...

Answer 10

The CE Smith Keel Roller for Boat Trailers - Self Centering #CE29505 is a replacement roller for a keel roller assembly. This self-centering roller fits a 12" wide bracket with a 5/8" shaft. In order to use this on your boat trailer you…

view full answer...

Answer 11

The best way to determine the height needed is to measure from the top of your trailer frame to the top of the sides of your boat. If the 40" Tall Guide-Ons #CE27626 sit right at or slightly above the sides of your boat then the shorter will…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...