CE Smith Roller-Style Guide-Ons for 20 ft Aquasport

Question

Question:

I know it’s says limits are 16-20 foot boats mine is 20 with a deep v will this product work for me ?

asked by: Tom

1

Helpful Expert Reply:

Yes, the CE Smith Roller-Style Guide-Ons for Boat Trailers - 15" Tall - 1 Pair item # CE27610 will work great with your 20' long boat. You will want to make sure your trailers frame is less than 3" wide x 4-1/4" tall. I have linked an install and review video for you to take a look at.

expert reply by: Jerred H

1

Answer 1

Unless you wanted to weld the uprights to your trailer frame above the step you would need to drill some hole in the step so that you can install the CE Smith Roller-Style Guide-Ons #CE27610 that you ordered.

view full answer...

Answer 2

You will want the boat to be close to touching the rollers on the CE Smith Roller-Style Guide-Ons #CE27610. Since the guide-ons are not meant to support weight you will want to place them so that they are fairly close to the boat but not too far.…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

Thank you for the pictures! For a replacement option I recommend the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K #DX29FR to replace your current actuator. The #DX29FR has a 7500lb trailer weight…

view full answer...

Answer 6

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 7

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 10

the CE Smith guide-ons #CE27610 are approximately 15 degrees off 90 degrees. So that would be 75 or 105 degrees depending on which way the guide-on was facing.

view full answer...

Answer 11

You are correct that the roller style guide-ons #CE27610 are not meant to support weight. But the boat brushing up against them is to be expected and they will work fine for that. A little bit of space like you said will help to make sure the boat…

view full answer...

CE Smith Roller-Style Guide-Ons for 20 ft Aquasport

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching