Recommended Base Rails For A 2003 Ford F-350 Super Duty

Question

Question:

I have a Curt Q20 5th Wheel. I need the Mounting Bracket and Rails for a Ford F350 Super Duty 4 door Dually 8’ bed 4x4. Do you carry this item

asked by: Vernon B

1

Helpful Expert Reply:

For a 2003 Ford F-350 you'll need the Curt Custom Fifth Wheel Installation Kit for Ford F250 and F350 # C16443-204 in order to mount your Curt Q20 5th Wheel Hitch # C16130.

expert reply by: Kevin C

1

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

To get the B&W Patriot #BWRVK3200 to work with your 2006 Dodge Ram you're going to need a set of 5th wheel rails #DM8552016-71. These rails are custom fit to your vehicle so they'll just bolt right up to the frame. It is worth mentioning…

view full answer...

Answer 8

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 9

Yes you are - all 5th wheel hitches are going to require some type of rails in order to be used. So you'd need #DM8552016-71 for your 2006 Dodge Ram.

view full answer...

Answer 10

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 11

It sounds like you could have a set of standard fifth wheel rails that most manufacturers use for their fifth wheel hitches to install into. The different manufacturers all make their own brand of rail kit, but they all have basically the same…

view full answer...

Answer 12

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Recommended Base Rails For A 2003 Ford F-350 Super Duty

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching