Gauge Wire for Extending Wiring of Air Lift Wireless Compressor

Question

Question:

I need to extend the wires for the compressor and the main unit for my wireless one. What gauge wire do each of them use?

asked by: Doug G

0

Expert Reply:

Air Lift doesn't have a specified gauge wire requirement for extending the wiring of the Air Lift Compressor kit part # AL25980EZ but based on the power requirements of the compressor I would go with 12 gauge wire like the part # 12-1-1 which we sell by the foot.

expert reply by: Jameson C

0

Answer 1

First, I have included a link to the installation instructions to the right for Air Lift kit #AL88299 for you. Using soapy water is the best way to find a leak in an air system. If it is leaking at a hose or fitting then replacing that hose or…

view full answer...

Answer 2

Thank you for your purchase from etrailer of the Air Lift WirelessONE Compressor #AL25980EZ. The pink wire is an optional ignition source connection and does not have to be hooked up; it will just allow the #AL25980EZ to make adjustments right when…

view full answer...

Answer 3

It sounds like the compressor system may not be getting power or is not waking up. Depending on how the Air Lift WirelessONE Compressor System #AL25980 is wired to your vehicle you may have to do additional steps. The wiring harness has a ignition…

view full answer...

Answer 4

First I recommend trying to determine exactly where the air is leaking from on your Air Lift LoadLifter 5000 Ultimate Air Helper Springs #AL88289 with Upgrade Kit #AL52301. The -4 AN Elbow Fitting #AL52RV could leak in one of 3 places. The AN/tapered…

view full answer...

Answer 5

When wiring up the Air Lift WirelessONE Compressor System for Air Helper Springs - Remote and Mobile App #AL25980EZ the power wire needs at least 15 amps to power the unit and the keyed power source that runs to the ignition switch circuit needs at…

view full answer...

Answer 6

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 7

Hey Dustin, thanks for reaching out! I will recommend SumoSprings over Timbrens all day everyday because they are much more forgiving when the vehicle is unloaded. We've actually joked around here about how the Timbren kits will either give you…

view full answer...

Answer 8

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 9

A 2023 Chevy Silverado 1500 will need to have 4WD and a two-speed transfer case, which will need to be placed in neutral, in order to safely flat tow. Your owner's manual will have a list of instructions to follow to switch your transfer case…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

The Air Lift WirelessONE Compressor System #AL25980EZ and Air Lift WirelessONE Compressor System #AL25980 are nearly identical with only some very minor differences in CFM and duty cycle ratings. The #AL25980EZ will also come with an easier mounting…

view full answer...

Answer 12

Mixing and matching the brackets and air springs isn't really recommended but you might be able to get a combination to work. If I were you I would just put the complete #AL88288 kit on since that would fit properly and there wouldn't be any…

view full answer...

Gauge Wire for Extending Wiring of Air Lift Wireless Compressor

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching