Troubleshooting Air Lift WirelessOne Compressor System Remote Not Pairing

Question

Question:

After replacing a fuse near the battery, the remote will not pair back up with the compressor. When the remote comes out of sleep mode, it comes up under the Devices and it says Scanning. No Devices are listed. The system is less than a year old and was paired previously for many months... Any advice would be greatly appreciated!

asked by: Glenn

0

Expert Reply:

It sounds like the compressor system may not be getting power or is not waking up. Depending on how the Air Lift WirelessONE Compressor System # AL25980 is wired to your vehicle you may have to do additional steps. The wiring harness has a ignition wire which if not connected to an ignition source will not wake up the compressor and manifold until it senses vehicle movement. You will want to check this wire for power if connected to a ignition source. If it is not connected you may need to drive the vehicle around before attempting to pair the Remote # AL72704.

expert reply by: Bud M

0

Corey

4/13/2024

I have the same problem it worked about 3 years flawless, now can’t get it to pair tried a new fuse and both remotes don’t work. My next step is to check if there’s power at the manifold. Is there anything else to check thanks in advance

Reply

Bud M.

4/15/2024

@Corey When you check for power getting to the manifold also check your ground connection as that could also cause it to have power issues.

Reply

Theuns L.

3/29/2024

Hello Bud I am having the same issues pairing issue after about 8 months of use it stopped, neither the remote or phone app works, both say no device found. Please reply

Reply

Alex L.

4/2/2024

@TheunsL I have the exact same thing. Installed in Oct 2023. It stopped working March 28 2024. The remote and the app doesnt work. says no device found or continues to sync. Tried power cycle, and tried removing the fuse.

Reply

Bud M.

4/3/2024

@TheunsL What tests and checks have you done? Have you confirmed power is getting to the manifold with a Test Light # PTW2993?

Reply

Ryan P.

4/4/2024

@BudM I’m having the same issue no resolution

Reply

See All (4) Replies to Theuns L. ∨

Answer 1

Start off by double checking that you have everything installed correctly and that you have installed two CR2032 batteries in your Remote for Air Lift WirelessONE Compressor Systems #AL72704. If you check out the attached clip from the instructions…

view full answer...

Answer 2

I went to the warehouse and pulled one of the Remote for Air Lift WirelessONE Compressor System, part #AL72704. I have attached a photo of the remote you can check out. On each side of the remote in the areas with the red arrows, there is a small…

view full answer...

Answer 3

Sounds like your air bag setup has a slow leak that is causing the compressor system to try and keep up too often. You should take some soapy water and spray on the bag, lines and where it connects to the Air Lift Compressor part #AL74000 to see if…

view full answer...

Answer 4

I can only recommend you go with the same amperage rating as what is called for in the install instructions of the Air Lift WirelessONE Compressor System for Air Helper Springs #AL25980 that you are installing. Since you want to use a circuit that…

view full answer...

Answer 5

Generally this is an issue with the remote #AL73002 communicating with the system #AL74000, a blockage, or a leak. I would inspect the compressor system and all of the air lines to make sure there are no issues. You can check for leaks using soap and…

view full answer...

Answer 6

No. If you don't have a remote to an AirLift WirelessONE system #AL25980EZ you can control this with the WirelessONE app on your phone or you can replace the compressor or you can get the part number off the manifold of the system to determine…

view full answer...

Answer 7

If your Air Lift WirelessONE Compressor System for Air Helper Springs #AL25980 is running constantly, then that would mean that you have a leak somewhere. You're going to need to check your air lines and your spring kit to identify the leaks and…

view full answer...

Answer 8

The fuse adapter that is included with the Air Lift WirelessAIR Compressor System part #AL74000 is optional therefore, it does not have to be used. However, you will need to run the power wire from the compressor relay directly to an un-fused side of…

view full answer...

Answer 9

Yes that is normal. If you let your 2014 Ford F-250 sit overnight (or a long period of time) then the Air Lift WirelessONE Compressor System #AL25980 should kick on because it is building pressure back up in the compressor. The system also kicks on…

view full answer...

Answer 10

We can definitely help set you up with air bags and a wireless compressor for your 2024 Chevy Silverado 2500 4WD long bed. Lets get right into it. For an air bag kit I recommend the Firestone Ride-Rite Air Helper Springs #F2613. I like the Firestone…

view full answer...

Answer 11

The best Air Lift air bags for your 2022 Chevy Silverado 1500 4x4 are the 5,000 lb option: - Air Lift LoadLifter 5000 Air Helper Springs #AL57288 The 5,000 lb capacity is the best for your truck because you won't need to come near that capacity,…

view full answer...

Answer 12

Thank you for your purchase from etrailer of the Air Lift WirelessONE Compressor #AL25980EZ. The pink wire is an optional ignition source connection and does not have to be hooked up; it will just allow the #AL25980EZ to make adjustments right when…

view full answer...

Troubleshooting Air Lift WirelessOne Compressor System Remote Not Pairing

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching