What is The Difference Between The Mount-n-Lock SafetyStruts Universal MO34VR & Standard MO22FR Kit?

Question

Question:

Looking at safety struts for my travel trailer. What is the difference between the MO22FR and the MO34VR.

asked by: A J

0

Expert Reply:

The Mount-n-Lock SafetyStruts Universal Kit # MO34VR includes the Standoff Spacers # MO54VR along with drill bits and the components found in the Standard Kit # MO22FR. The standoff spacers allow for mounting on I-beams shorter than 6".

expert reply by: Bud M

0

Answer 1

From how you're describing your set up, it sounds like your bumper is attached to a tube frame, and there is a way for you to install the support brackets, which are the following part number: - Mount-n-Lock SafetyStruts Universal RV Bumper…

view full answer...

Answer 2

You could weld the Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames #UF35-946403 to the box frame that's welded to the frame of your 2019 Grand Design Imagine 2600RB travel trailer but would need to have a fabricator come out…

view full answer...

Answer 3

The Safety Struts you have now on your RV frame/bumper would work well with the 24x60 etrailer Cargo Carrier for RV Bumper #e99049 that you mentioned. You can use them instead of the brackets that come with the carrier and you'd be perfectly…

view full answer...

Answer 4

All of our cargo carriers like the 24x60 etrailer Cargo Carrier for RV Bumper #e99049 you checked out all come with the support brackets. Currently, we do not offer the cargo carrier without the support bracets.

view full answer...

Answer 5

Thanks so much for that detailed info, and we do indeed have a trailer hitch for your Jayco trailer with an I-beam frame with a 68 inch inside width, from Curt: - Adjustable Width Trailer Hitch Receiver for RVs, 22" to 72" Wide #13703 The…

view full answer...

Answer 6

Many RV bumper manufacturers construct their product with a plastic cap or a hinged door instead of endcap, allowing bumper to be used for storage; apparently you have this type. Open that end piece to examine if the seam has spot welds (short welds…

view full answer...

Answer 7

Yes, the Trailer Bumper Hitch Receiver, part #E-100, can be used on towable pop-up camper units with up to a 4 inch square bumper. However, you cannot exceed the limits of your camper bumper. The bumper towing and tongue capacities may be indicated…

view full answer...

Answer 8

I went out to our warehouse and measured the thickness of the L-Brackets on the Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames #UF35-946403 and measured .34" or 11/32" thick. As per the second question, you are not going to be…

view full answer...

Answer 9

You'd need to box the I-beam frame where you plan to install the Ultra-Fab 2" Trailer Hitch Receiver #UF35-946403 and then you can weld it in place. You'd need to weld around the L-bracket basically of the hitch to the frame. See…

view full answer...

Answer 10

The Mount-n-Lock SafetyStruts Universal RV Bumper Support Brackets - 4" to 4-1/2" #MO34VR will increase the RV bumper's weight capacity to 400lbs. This will fit 4" - 4-1/2" bumpers which looks to be what is on the 2017 Avenger…

view full answer...

Answer 11

For an I-beam frame trailer I have a better solution than the #UF35-946403 that you referenced. Instead you would want the part #13703. I attached a picture that I took from that attached install instructions that shows how it would install on an…

view full answer...

Answer 12

The 24x64 etrailer Cargo Carrier for RV Bumper #e83YR is going to come with the Standard Supports #MO22FR. If you have an I-Beam frame that you'll be attaching to then you'll want the Universal Kit #MO34VR instead.

view full answer...

What is The Difference Between The Mount-n-Lock SafetyStruts Universal MO34VR & Standard MO22FR Kit?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching