Does The etrailer RV Bumper Cargo Carrier Come With The Universal Safety Strut Kit

Question

Question:

Does the universal mount n lock Safety struts come with the 64in Bump. Rack ?

asked by: Stan E

0

Expert Reply:

The 24x64 etrailer Cargo Carrier for RV Bumper # e83YR is going to come with the Standard Supports # MO22FR. If you have an I-Beam frame that you'll be attaching to then you'll want the Universal Kit # MO34VR instead.

expert reply by: Kevin C

0

Answer 1

While we don't have a way to mount the Bumper RV Cargo Carrier #e83YR to the rear of an RV without a bumper a similar solution that could work for you would be a frame mounted carrier that mounts under the RV like with the Lippert part…

view full answer...

Answer 2

Yes, you will use the Mount-n-Lock SafteyStruts Universal RV Bumper Supports #MO34VR to reinforce your bumpers frame on your 2022 Jayco Jay Flight SLX 242BHS Travel Trailer. These brackets will be installed by bolting through your trailers frame,…

view full answer...

Answer 3

The Mount-n-Lock SafetyStruts Standard RV Bumper Support Brackets - 4" to 4-1/2" #MO22FR and Mount-n-Lock SafetyStruts Universal RV Bumper Support Brackets - 4" to 4-1/2" #MO34VR. Use #MO22FR for standard bumpers…

view full answer...

Answer 4

For the 24x64 etrailer Cargo Carrier for RV Bumper, #e83YR I recommend using the Fulton Economy Spare Tire Carrier, #FETCLB0201 to mount your spare to hang under the cargo carrier.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 9

Yes, the 24x64 etrailer Cargo Carrier for RV Bumper, #e83YR is the built the same as the shorter version but with an extension to increase width. From the images you attached, if you remove the spare tire, you can install the 24x40 etrailer Cargo…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

Yes the brackets of the 24x64 etrailer Cargo Carrier for RV Bumper #e83YR that you referenced would get bolted to the frame rails under the bumper to give it more support so that you could carry heavier items like generators.

view full answer...

Does The etrailer RV Bumper Cargo Carrier Come With The Universal Safety Strut Kit

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching