How Does Ultra-Fab 2" Trailer Hitch Receiver # UF35-946403 Attach to I-Beam Frame

Question

Question:

How do you weld this to the an I-beam trailer frame?

asked by: Jonathan S

0

Expert Reply:

You'd need to box the I-beam frame where you plan to install the Ultra-Fab 2" Trailer Hitch Receiver # UF35-946403 and then you can weld it in place. You'd need to weld around the L-bracket basically of the hitch to the frame. See picture.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames #UF35-946403 is an adjustable hitch that will fit inside 2002 Nash 19I with I-beam frame as long as you have clearance at the rear when inserted on the inside of your I-beam. It is…

view full answer...

Answer 2

The Ultra-Fab Hitch #UF35-946403 weighs 50 lbs; I went to the warehouse to measure how far the receiver extends away from the tube and found it to be approximately 5-3/4". As for how the Ultra-Fab welds onto an I-beam frame I contacted the…

view full answer...

Answer 3

Step 8 in the instructions for the Ranch Hitch Universal 5th-Wheel-to-Gooseneck Coupler Adapter #AM3100 states the following: 8) Locate the grade 8 bolts, lock washers, nuts and your drill and bit. There are eight holes drilled in the Ranch Hitch…

view full answer...

Answer 4

I have attached a photo with the mounting dimensions of the Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames part #UF35-946403. The brackets are 2" long x 4" wide x 3" tall. If you need any other measurements then please let…

view full answer...

Answer 5

For a 70 lb E-bike with fat tires we really only have one option that will work well. That's the Hollywood Racks #HLY84FR that has a weight capacity of 80 lbs per bike and can accommodate tire widths of up to 5 inches. It can also carry up to two…

view full answer...

Answer 6

The Mount-n-Lock SafetyStruts Universal Kit #MO34VR includes the Standoff Spacers #MO54VR along with drill bits and the components found in the Standard Kit #MO22FR. The standoff spacers allow for mounting on I-beams shorter than 6".

view full answer...

Answer 7

You could weld the Ultra-Fab 2" Trailer Hitch Receiver for Trailer Frames #UF35-946403 to the box frame that's welded to the frame of your 2019 Grand Design Imagine 2600RB travel trailer but would need to have a fabricator come out and look…

view full answer...

Answer 8

I went out to our warehouse to take a look at the Ultra-Fab 2" Trailer Hitch Receiver #UF35-946403 referenced in your question. The smaller inner crosstube measures 2 inches x 2 inches and the outer crosstube measures 2-1/2 inches x 2-1/2…

view full answer...

Answer 9

From how you're describing your set up, it sounds like your bumper is attached to a tube frame, and there is a way for you to install the support brackets, which are the following part number: - Mount-n-Lock SafetyStruts Universal RV Bumper…

view full answer...

Answer 10

The Curt #C13704 hitch can be used on a trailer with frames up to 66” wide. For frames up to 68-3/8” wide order the Lippert #LC240220, or if you need smaller order the Curt #C13701 for frames up to 51” wide. This last Curt hitch has a 2” drop that…

view full answer...

Answer 11

Okay let's get started here with the suspension for your 2012 Skyline Koala 27CDS with 3,500 lb Axles; for the first part regarding your equalizers and suspension upgrade kit, so long as your current equalizer is spaced 6 inches (or close to it -…

view full answer...

Answer 12

All of our cargo carriers like the 24x60 etrailer Cargo Carrier for RV Bumper #e99049 you checked out all come with the support brackets. Currently, we do not offer the cargo carrier without the support bracets.

view full answer...

How Does Ultra-Fab 2" Trailer Hitch Receiver # UF35-946403 Attach to I-Beam Frame

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching