Replacement Parts for Trailer Hub # 8-219-9UC3-A

Question

Question:

Hi I’m looking for the parts included in drum assembly 8-219-9UC3-A. I need everything except the drum itself. Do you sell that as a kit or do I need to piece it together? Thanks in advance.

asked by: Justin C

0

Expert Reply:

Here are all the replacement parts for the hub part # 8-219-9UC3-A:

Replacement bearing # 25580
Race # 25520
Bearing # 14125A
Race # 14276
Seal # 10-63
Oil cap # RG04-230

expert reply by: Jameson C

0

Answer 1

The torque requirements for leaf spring u-bolts depend on the diameter of the u-bolts that are being used. If the gross weight of your tandem axle trailer is 7,000 lbs, then you likely have two 3,500 lb axles. Typically 1/2 inch diameter u-bolts are…

view full answer...

Answer 2

We sure can! The spacing you're looking for between the hangers for the Triple-Axle Trailer Hanger Kit for 2" Slipper Springs #AP302-H302 is 28-1/2" for the first to second hangers, 33" from the second to third hangers, and then…

view full answer...

Answer 3

The proper positioning of leaf spring hangers will be up to the installer. Therefore, in order to get the correct leaf spring hanger positions for the Triple-Axle Trailer Hanger Kit for 2" Slipper Springs part #AP302-H302 you'll need to mock…

view full answer...

Answer 4

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 5

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 8

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 9

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 10

Hey Patrick, so for your leaf spring upgrade I am going to need to know a couple of things before I can get you over to the right part. Specifically, the length from eye to eye, the spring width, leaf thickness, and the number of leaves. From here I…

view full answer...

Answer 11

Yes, going from a 4 leaf to a 6 leaf spring would add slightly to your ride height. For example, if the current 4 leaf spring has 3/8" thick leaves, and you go to a 6 leaf spring with 3/8" thick leaves, you would be adding 3/4" of…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Replacement Parts for Trailer Hub # 8-219-9UC3-A

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching