Replacing A Dexter P-29 Axle Made Around 1999

Question

Question:

I have a 1999 double axle camper trailer with Dexter P-29 Model SLR SN 0 3293 727 / D 28 12 7 / 2800 max capacity axles. What would be a direct replacement axle for my camper? Thanks!

asked by: Brad P

0

Expert Reply:

I reached out to my contact at Dexter for more information on this axle. I was told that the axle tag is too old, and they no longer have information available on these axles.

I very well may have an axle that will replace yours. I would need to confirm a few specs with you first. Since we do not carry any 2,800 lb axles, I would be looking at a 3,500 lb axle as a replacement. We would want to know the overall length of the current axle, measured across from hub face to hub face. The axles I carry in this size are either 89" long # T3584F-8974, or 95" long # 7359765.

I would also want to confirm the distance between the spring seats on the current axle. Assuming your axle is a round tube leaf spring axle of course. The spring seats on our axles will be at either 74" or 80" on center. We can always provide you with a few loose spring seats # TRSS238, if our axle does not match up exactly.

We also have axle-less suspension options available. If you are interested I recommend going with the Timbren # ASR3500S05. This is the standard duty 3,500 lb setup. It is basically a torsion axle without a crossmember. Rubber torsion springs built independently in each side will reduce road shock and rattle without the need for leaf springs. These are a bit more on the expensive side, but offer great performance especially off-road. I have linked a few videos highlighting this product below for you to take a look at.

I have hubs available that will work with all of the axles I mentioned above part # AKIHUB-545-35-EZ-K. This is a 5 on 4-1/2" easy grease hub.

expert reply by: Jesse M

0

Answer 1

I contacted our representative at Redline and he informed me that the Single-Axle Trailer Hanger Kit for Double-Eye Springs - 3-1/4 Front, 1-1/2 Rear, part #APS4, must be welded to the trailer frame. He informed me that there should be a hole to make…

view full answer...

Answer 2

There are many ways you can secure wires to a trailer. I would not recommend the use of tape as it will wear out quickly when exposed to the elements. Soldering is also not recommended because it is a more permanent method and you may need to change…

view full answer...

Answer 3

An axle without idler hubs would not have a left or right side assigned to it. It could basically be ran either direction. If it has brake assemblies installed though then it would need to face the right direction. Otherwise you'd have to swap…

view full answer...

Answer 4

Trailer axles are supposed to have a bow in them that faces down towards the ground. With the weight of the trailer normally this flattens out slightly and gives you the correct camber you need. Whoever flipped your axle should have used an over…

view full answer...

Answer 5

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 8

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 9

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 10

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...