Are the CE Smith Carpeted Bunks Made with Treated Wood

Question

Question:

I am looking at the C E Smith carpeted trailer bunks. Are these made with treated lumber? Thanks

asked by: Bill W

1

Helpful Expert Reply:

The CE Smith bunk boards, part # CE27845, are made from untreated southern yellow pine 2 x 4's.

expert reply by: Jameson C

1

Answer 1

I have a solution for you, but unfortunately those 7ft long bunk boards #CE27845 are going to be the longest ones we currently offer. If you wanted to source the wood yourself you could then just use some marine grade carpeting like the CE Smith…

view full answer...

Answer 2

I've had to do this before, so I understand your concern about the carpet getting shredded. What I did was take a sharp utility knife and cut a small X right where I wanted to drill my holes. This worked very well and didn't rip up the…

view full answer...

Answer 3

Provided that the widest part of the I-Beam frame is no wider than 3 inches and the overall height no more than 4-1/4 inches you could use CE Smith Bunk-Style Guide-Ons #CE27600 with the I-Beam frame. The fact that the frame is aluminum should not be…

view full answer...

Answer 4

You certainly could make your own bunk boards using pressure treated lumber and bunk carpet like #CE11372 if you wish. CE Smith doesn't use pressure treated lumber in their bunk boards because some of the chemicals used to pressure treat the…

view full answer...

Answer 5

The CE Smith Post-Style Guide-Ons for Boat Trailers part #CE27648 are universal fit boat guide-on designed for I-beam trailer frames up to 4" wide. The closer to the rear they are installed, the more they will assist with loading. That said, you…

view full answer...

Answer 6

The best way to determine the height needed is to measure from the top of your trailer frame to the top of the sides of your boat. If the 40" Tall Guide-Ons #CE27626 sit right at or slightly above the sides of your boat then the shorter will…

view full answer...

Answer 7

Choosing the correct guides is a little different for each boat/trailer combo but we do have a few options that you can choose from. I recommend going with either the CE Smith Bunk-Style Guide-On Kit #CE27600K90 where you supply your own 2x4 boards…

view full answer...

Answer 8

I was able to track down some measurements for the 90 degree uprights that are included with the #CE27600K90 bunk kit. Hope this helps. See below: A: Internal Distance - 15-1/2" A: External Distance - 17" B: Internal Distance - 18" B:…

view full answer...

Answer 9

One solution could be to install one of the bunks of the CE Smith Bunk Guide Ons #CE27660 in front of and behind the fender wells of your trailer since we don't have any longer than 5 feet like the kit part #CE27600.

view full answer...

Answer 10

The CE Smith I-Beam Clamps for Boat Trailers, part #CE27682A are designed for trailer that have an I-Beam 2-1/2 to 4-1/2 inches wide. It seems odd that one side stays on and the other side keeps falling off on your trailer. I do not recommend using…

view full answer...

Answer 11

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 12

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Are the CE Smith Carpeted Bunks Made with Treated Wood

Product Page this Question was Asked From

Continue Researching