Weight of Timbren Axle-Less Trailer Suspension

Question

Question:

What is the weight of the 3500 lb. Torflex axel and what is the weight of the same 2200lb. torflex axel?

asked by: Tom

0

Expert Reply:

The Timbren Axle-Less Trailer Suspension # ASR1THDS01 weighs 159 lbs. The 3,500 lb system # ASR3500S05 weighs 145 lbs.

expert reply by: Robin H

0

Answer 1

We have Jeep style trailer fenders but only for up to 15 inch wheels. We don't have any fenders for 17 inch wheels unless you are referring to the overall diameter of the tire versus the wheel/rim. I haven't seen any tear campers with that…

view full answer...

Answer 2

I went out into our warehouse and measured an etrailer Trailer Fender #HP76VR and found that from the ground straight up to the midpoint of the radius it measures 17-3/4 inches and measured from where the leg touches the ground to the midpoint of the…

view full answer...

Answer 3

I went out to the warehouse and pulled the two fenders and took the measurements you requested of each one. The dimensions of the etrailer Trailer Fender #HP99VR from the side starting from the ground straight up to the midpoint of the radius…

view full answer...

Answer 4

The Single Axle Trailer Fender #HP76VR that you referenced would work well on your ATV trailer, but these do not have a weight rating so I would not recommend you drive your ATV over them. There should be a way to load your ATV's without…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 12

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...