Is 4-Bolt Brake Flange Needed to Install 3,500 lb Hub & Drum AKHD-655-35-K
Question:
I’m rebuilding a 1970s Manorette camper. # AKHD-655-35-K has the dimensions I need. My existing hum and drum assembly has a four bolt pattern to attach it to a plate on the back side. I did not see this called out on the website. Do I need to use them?
asked by: Joe
Expert Reply:
Good question but no, the 4-bolt brake flange is not a requirement to install the Trailer Hub and Drum Assembly - 3,500-lb Axles # AKHD-655-35-K.
The hub will still fit your spindle and install just fine, but you will need that 4-bolt brake flange if you were also installing brakes that fit the hub like the Dexter Hydraulic Trailer Brake Kit # 23-312-313 or Dexter Electric Trailer Brake Kit # 23-26-27.
(click to enlarge)
Products Referenced in This Question
Dexter Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3.5K
- Trailer Brakes
- Electric Drum Brakes
- Standard Grade
- Manual Adjust
- 10 x 2-1/4 Inch Drum
- 3500 lbs Axle
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Dexter
more information >
Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 6 on 5-1/2 - Pre-Greased
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Pre-Greased
- Standard
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 6 on 5-1/2 Inch
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- etrailer
more information >
Product Page this Question was Asked From
Dexter Hydraulic Trailer Brake Kit - Uni-Servo - 10" - Left and Right Hand Assemblies - 3.5K
- Trailer Brakes
- Hydraulic Drum Brakes
- Standard Grade
- Manual Adjust
- Single Servo
- 10 x 2-1/4 Inch Drum
- 3500 lbs Axle
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Dexter
more information >
Continue Researching
- Shop: Demco Hydraulic Brake Actuator - Drum - Zinc - 2" Ball - 7,000 lbs
- Shop: Brake Controller
- Q&A: Available 6K Weld-On A-Frame Drum Brake Actuators
- Q&A: Mounting Bolt Dimensions of Demco Actuator DM72VR
- Q&A: Solution for Needing Replacement Parts for Atwood Surge Brake Coupler
- Q&A: How To Determine If Demco Actuator For Drum Brakes Will Fit
- Search Results: 23~312~313
- Search Results: akhd~545~35~ez~k
- Video: Review of Demco Brake Actuator - Surge Brake Actuator - DM72VR
- Shop: Dexter Trailer Hub and Drum Assembly for 3,500-lb Axles - 10" Diameter - 5 on 4-1/2
- Shop: Dexter Nev-R-Adjust Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Shop: Dexter Hydraulic Brake Kit - Free Backing - 10" - Left and Right Hand Assemblies - 3,750 lbs
- Shop: Hydraulic Brake Kit - Uni-Servo - Free Backing - Dacromet - 10" - Left/Right Hand - 3,500 lbs
- Q&A: Replacement for Atwood 61101 Brake Actuator
- Shop: Trailer Wiring
- Search Results: trailer brake controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Choosing the Right Brake Controller
- Video: Demco Hydraulic Brake Actuator Review
- Article: Trailer Wiring Diagrams
- Search Results: brake controller
- Shop: Trailer Hitch
- Q&A: Can the Replacement Atwood Master Cylinder 85736 Still Be Obtained
- Q&A: Bolt Pattern for Demco Hydraulic Brake Actuator DM72VR
- Article: Brake Controller Installation: Starting from Scratch
- Shop: Suspension Enhancement
- Search Results: brake actuator
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
on Trailer Brakes
