Single or Double Axle Lift Kit For Lance 1885 Travel Trailer

Question

Question:

I want to get a lift kit for my 2012 Lance 1885 Travel Trailer. But I am not sure if I should get the #K71-707-02 or the #K71-707-01. Thanks for your help getting the right part

asked by: Troy P

1

Helpful Expert Reply:

For your 2012 Lance 1885 Travel Trailer, between the two lift kits you mentioned, you will want the double axle kit, which is the following part number:

- Torflex Lift Kit - Tandem Axle # K71-707-02

expert reply by: Kyle S

1

Answer 1

Per the manufacturer the correct kit you would need for your 2011 Lance 1985 Trailer with Dexter Axle #2544334 is The Torflex Lift Kit #K71-707-01. The Lift Kit #K71-707-02 is not the correct kit. This lift kit will raise your trailer frame to…

view full answer...

Answer 2

Based on some research, I was able to find out that your tandem axle 2019 Lance 1995 travel trailer has a GVWR of 5,700 lbs, and does use Dexter Torflex torsion axles like you mentioned, so the correct lift kit is the Torflex Lift Kit - Tandem Axle…

view full answer...

Answer 3

Yes, the 2020 Airstream Globetrotter 27 uses Dexter Torflex #11 Axles so the Torflex Lift Kit part #K71-724-02 will work.

view full answer...

Answer 4

In order to choose the correct Torflex Lift Kit like part #K71-725-02 you'll need to know the axle model. The above for example is for a model #12. The model can be found on the axle tag sticker located on the axle tube. I have attached a full…

view full answer...

Answer 5

The 2012 Chevy Suburban didn't have a plug under the dash for a brake controller installation, it has a bundle of loose wires under the dash above the emergency brake pedal assembly, as shown in the provided photo. The pigtail from your #90195 P3…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

The spring hanger placement is going to be determined by your axle spacing. For example, if your axles are spaced 33 inches apart, as shown in the attached diagram, a 7K axle slipper spring, like #e74SR, requires a distance of 28-1/2 inches between…

view full answer...

Answer 10

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...