Will Sportframe Drawbar # 3594 Fit Kubata RTV Receiver
Question:
I want to use this on our RTV Kubota. to get the pin in, It only can go two inches deep before it butts up against the axel. Can this unit work?
asked by: Robert
Expert Reply:
I pulled a Sportframe Drawbar, part # 3594, from our warehouse and took a measurement for you. As the attached photo shows the distance from the end of the shank that inserts in the receiver on your Kubata RTV to the center of the hitch pin hole is 1-1/2 inches. This drawbar is designed to fit 1-1/4 inch receivers.
You mentioned that you have 2 inches before it hits the axle. The best way to see if this will work is to take a ruler and insert it in the receiver on your RTV. If you have more than 1-1/2 inches inside the receiver on your RTV from the center of the hitch pin hole to where it stops, or bottoms out, this would work for you.
Product Page this Question was Asked From
Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Rise - 4 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- Draw-Tite
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Draw-Tite Drawbar for 1-1/4" Hitches - 4" Rise - 10" Long - 2,000 lbs
- Shop: Trailer Hitch
- Video: Draw-Tite 1-1/4 Inch Hitch Drawbar Review
- Search Results: draw bar
- Shop: Curt Class I Drawbar - 5" Rise - 9-9/16" Long - 2,000 lbs
- Shop: Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: Curt Class I Drawbar - 4" Rise - 9" Long - 2,000 lbs
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Video: Trailer Hitch Installation - 2010 Volkswagen Golf - Curt
- Article: How to Measure for Trailer Hitch Drop
- Shop: Curt Class II Drawbar - 5" Rise - 9-5/8" Long - 3,500 lbs
- Shop: Curt Class II Drawbar - 5" Rise - 11-5/8" Long - 3,500 lbs
- Article: My Trailer Hitch Doesn't Fit
- Video: Yakima Rack and Roll Trailer Review
- Search Results: 4"
- Search Results: 4" rise
- Shop: Trailer Wiring
- Video: Inno Hitch Bike Racks Review - 2019 Hyundai Santa Fe
- Video: Review of etrailer Hitch Alignment - Hitch Pin Alignment Collar - e98942
- Q&A: Will the Curt Part # C11401 Fit a 1998 Mustang Cobra
- Q&A: Installation Video For Curt Class I C11041 Hitch on 2001 Ford Mustang
- Q&A: Recommended Trailer Hitch and Adapter for 2011 BMW 328i Sedan
- Video: Curt 19x60 Hitch Cargo Carrier Review - 2020 Chevrolet Equinox
- Video: Curt Hitch Cargo Carrier Review - 2012 Hyundai Elantra
- Q&A: Pin Hole to Hitch Opening Distance on 2 inch and 1-1/4 inch Hitches
- Search Results: class 1 drawbar
- Q&A: Does Curt Hitch # C11041 Fit 1994 Ford Mustang with 5.0 Liter V8
- Search Results: trailer hitch
- Search Results: drill bit
- Search Results: hit h
on Trailer Hitch Ball Mount
